Question about 2005 Hyundai Elantra

Open Question

Where is the tcm relay switch on elantra 2005

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the TCM in my 2005 Chevy colbolt, light come on but car won't start, turn key and anti theft icon comes on but doesn't stay on


TCM ? transmission control module ? Did you have it programmed ? Reprogram the TCM. Refer to Control Module References for programming and setup information.
Transmission Control Module Programming and Setup
The transmission control module (TCM) must be programmed with the proper software/calibrations. Ensure that the following conditions exist in order to prepare for TCM programming:
• The battery is fully charged.
• The ignition switch is in the RUN position.
• The Techline equipment cable connection at the data link connector (DLC) is secure.
Program the TCM using the latest software matching the vehicle. Refer to up-to-date Techline equipment user instructions.
If the TCM fails to program, proceed as follows:
3.1. Ensure that the TCM connection is OK.
3.2. Inspect the Techline equipment for the latest software version.
3.3. Attempt to program the TCM. If the TCM still cannot be programmed properly, replace the TCM.

Feb 08, 2017 | 2005 Chevrolet Cobalt

1 Answer

What is the p0886


code p0886 refers to transmission control module(TCM) power relay--control circuit low===causes wiring short to ground--TCM power relay--TCM
Check for water in the wires and connections--- check the power relay or replace .
As the TCM controls the gear selection and you have made no mention of gear problems , I would be looking at the relay

Aug 10, 2014 | 2005 Smart Cabrio Passion

1 Answer

The alarm is randomly going off on my 2005 hyundai elantra


there is a theft/locking control module under the dash. sometimes they go bad. have you check the relay

Jan 27, 2013 | 2005 Hyundai Elantra

1 Answer

What is meaning p1529 on my elantra


P1529 means the TCM (transmission control module) has requested that the ECM (engine control module) turn on the check engine lamp. All I can tell you based on this information is that the TCM has seen something abnormal. To find out what abnormal condition the TCM saw, you'd need to retrieve the DTCs (diagnostic trouble codes) from the TCM. The most frequent culprit is either the input or output speed sensor, but there's no way to know whether they may be the issue without the TCM DTCs

Mar 20, 2010 | 2004 Hyundai Elantra

1 Answer

Have a question about 2005 Elantra.When I turn off ignition headlights go off. is it possible to keep headlights on with ignition off?


no its not possible most newer cars like 05's and older have a automatic relay so when ignition is off they automatically shut off so you dont forget about them and drain your battery

Dec 26, 2009 | 2005 Hyundai Elantra

1 Answer

Code p1613 on a 1998 hyundai elantra means what


P1613 trouble code. When you start the engine, the TCM (transmission control module) sends a test signal along the wire to the ECM (engine control module) it uses to request the check engine lamp. P1613 indicates that the test signal voltage is more than 120% of battery voltage.

I'd recommend clearing the code to see if it comes back. It's possible this was a one-time error. If it does come back, it'll be very difficult to diagnose. The problems could be:
1. Improper signal from TCM (defective TCM)
2. Improper signal measurement in ECM (defective ECM)
3. Irregular feedback from an actuator that causes bleed-over into this signal circuit in either the ECM or TCM.

The last case of this I recall was a defective TCM

Oct 30, 2009 | 2000 Hyundai Elantra

1 Answer

Error code p1529 trans problem it is in default third gear and pops/jolts when you first start going foward


P1529 is generated by the Transmission Control Module (TCM). It is simply to tell the ECM to turn on the MIL/Check Eng light because the TCM detected a malfunction and has set a DTC in the TCM.
On top of the tranny, by the selector lever, there is the range switch. Disconnect, clean therminals, add some dielectric gears to the terminals, and reconnect. Disconnect negative battery terminal for 30+ sec., reconnect terminal, drive car and see if MIL come on again

Sep 14, 2009 | 2006 Hyundai Elantra

1 Answer

Check engine light on 2005 town and country 3.3


(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Apr 11, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...