Question about 2004 Ford Escape

Open Question

Diagram how to replace 2003 ford escape coil pack

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2003 Ford Taurus spark plug diagram

Have a look here.

http://www.autozone.com/N,26200242/shopping/specsSelect.htm

Posted on Feb 02, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: 2005 ford escape assembly diagram for the front axle

If they are sealed bearings, you will need a press to get them out. If they are bolt in, just remove the brake pads/rotors, then the axle nut, then the bolts holding the wheel bearing in. Install in reverse order.

Posted on Mar 07, 2009

  • 6 Answers

SOURCE: headlight went out in 2003 ford escape i have

you have to remove the whole headlight assembly, then pop off the front cover pull the old bulb out and put the new one in. reverse the process to re-install. there is a small plastic tab on the topfront of the headlight assembly, that is what you need to release to get the clear cover off and get inside.

Posted on Oct 07, 2009

  • 312 Answers

SOURCE: Ford Escape 2003. Engine suddenly overheat.

Engine over heating can be caused by a number of things. When you say the water pump and radiator appear to be ok I am also guessing that you checked the coolant level to make sure it is normal.

If the level is low then you obviously have a leak. Insufficient coolant circulating will not cool the motor properly because it won't be able to draw enough heat out. If the level is normal then you need to check the thermostat to make sure it is opening properly. To do this, run the motor to temperature and check the top and bottom hoses. They should both be hot and firrm once the thermostat opens meaning the circulation loop is operating properly. If the top is hot and firm and the bottom is cold/soft or collapsed then the thermostat isn't opening.

If the thermostat is operating properly then you ned to look for some other obstruction or cause for coolant loss. Check the head/intake gaskets, hose connections, hoses, over flow tank, radiator fins, radiator side tanks etc..

Good luck.

Posted on Jun 10, 2010

Testimonial: "Thank you for your quick response. I will get the head/intake gasket checked."

  • 45 Answers

SOURCE: how to change ignition coil pack on 2003 ford

the coil pack is located on nthe back valve cover, bank1, towards the firewall.
it mounts with three bolts or torx screws.
it is kinda hard to get to but just pull off the plugwires and
it will give you more room.
there is also i radio capacitor thing that is retained by one of the bolts,

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What coil pack will interchange with 2003 escape 3liter


Only the one that is intended for this engine will work.

Sep 05, 2016 | 2003 Ford Escape

1 Answer

I NEED TO KNOW WHERE ARE LOCATED THE SPARK PLUGS OF A ESCAPE 2003


You will have to remove the engine cosmetic cover. The 2.0 four cylinder has 1 and the 3.0 V6 has two The 2.0 is a standard single coil pack and will be clearly visible when you take the cover off, just follow the wires and remove the spark plug boots and voila. The V6 uses 6 coil packs and you will have to unscrew their bolts and remove each of them to get at the spark plug underneath them. Make sure you blow away any debris, from around the plugs before taking them out. hope this helps

Mar 28, 2011 | 2003 Ford Escape

1 Answer

My ford escape 2003 2.0 move roughly. a mechanic diagnosed it that my car's n0.4 coil pack was not functioning and it needs replacement.he however did not check if my no. 4 spark plug needs to be the one...


swop no4 plug with another one and see if its the same ,if mechanic diagnosed coil pack then i do feel he would be right as the symptoms are different

Oct 22, 2010 | Ford Escape Cars & Trucks

3 Answers

Need firing order diagram for a 5.4 ford expedition


Check this diagram for 2003 Ford Expedition 4WD 5.4 liter SOHC V-8 VIN "L"...

4867d57.gif

Hope helps (remember rated this help).

Jul 05, 2010 | 2003 Ford Expedition

1 Answer

I need a negative lock/unlock relay for a 2003


i don't have a wireing diagram for you but all relays use power to pin 86 or 85 and ground to pin 86 or 85 does't matter as they just energize a coil in the relay.pin 30 is either a power or a ground depending what you want switched.when the relay is activeated pin 87 becomes the same as pin 30.pin 87a is rarely used but it will be the same as pin 30 only when the relay is not activated.hope this helps.

Sep 30, 2009 | 2003 Ford Escape

1 Answer

2005 FORD ESCAPE


You will have to replace valve cover gaskets and the orings around the spark plug wells.The oring is what is causing the problem.You will also need to replace the coil pack boot.You can get this seperate you don't have to replace the whole coil pack.

Feb 26, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2004 Ford Escape Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...