Question about 2005 Cadillac STS

Open Question

Fender removal on 1999 cadillac - 2005 Cadillac STS

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the front right fender of my 1995 Cadillac Deville


Tool`s needed 3/8 drive socket set.
i`m assuming you want to remove the outer finder.
to remove fender locate the row of bolts along the inside after you open the hood under the splash Gard and the inner wheel well and a few in and around the grille maybe even in the door cavity .
Start at the bottom and work up saving the top row for last

Oct 31, 2016 | Cadillac Cars & Trucks

2 Answers

How do you remove the front fender


Tool`s needed 3/8 drive socket set.
i`m assuming you want to remove the outer finder.
to remove fender locate the row of bolts along the inside after you open the hood under the splash Gard and the inner wheel well and a few in and around the grille maybe even in the door cavity .
Start at the bottom and work up saving the top row for last.
to install just reverse.
Good Luck and take your time

Jul 02, 2014 | 1993 Cadillac DeVille

1 Answer

Where are the computers located on an 1999 cadillac deville


1 is located under the hood on the side of the drivers side fender, and the second computer is located in behind the kickpanel inside the car just in front of the passenger door. it is located on the wall, not under the carpet !!

Nov 17, 2010 | 1999 Cadillac DeVille

1 Answer

My husband hit the drivers side of the fender it has come loose so it rubs on tire how do you put it back on right?


You can use self tapping screws to get it back on, or remove the fender by removing the bolts under hood, mudflap and bumper, then pound the dent out and make it straight again. Or just try and pound it straight.

Sep 02, 2010 | 1999 Cadillac DeVille

1 Answer

Procedure to change turn signal light bulb on a


Remove 3 or 4 of the plastic pins holding the inner fender. They are located around the lip of the fender opening. The pins are removed by pulling the center cap of the pin straight out about an 1/8" and then wiggle and pull the whole pin out.
Pull the inner fender down and back.
Reach your arm in and grab the socket and squeeze the locking tab.
Rotate the socket counter-clockwise less than a quarter turn, and pull straight back.
Reach your other hand in and remove the bulb by pulling it straight out of the socket. It takes a 3157 bulb

Mar 30, 2010 | 2005 Cadillac CTS

1 Answer

My 99 cadillac diville message stater disabled


If you have a key with a resister in it , it may be the ignition cylinder itself. If you do not have a resister in your key , you should check for bad body grounds along the fenders and firewall. You can also try disconnecting the battery negative cable for 20 secs. and retry.

Jul 20, 2009 | 1999 Cadillac DeVille

1 Answer

Cadillac antenne 1976


its has a hole through the fender for the mast to come through and a brace at the motor housing to attach to the inner fender support. a threaded antenna bezel is needed to mount the mast to the fender

May 25, 2009 | 1976 Cadillac Deville

1 Answer

Replacing the Right Front Fender on a 1999 Mazda 626


Can you remove the wheel well splash shield and get access to the bolts? Body shop techs have a special tool to get into this area.

Here's a 97 Probe whcih was the same as a 626 in 1997:

Fender, Front Removal
  1. On GT models, remove the side sill extension. Refer to Section 01-08 for the removal and installation procedure.
  1. Remove the front fender bolt located in the door jamb opening.


    RH Side Shown, LH Side Similar


    b7b1239.gif

  1. Remove the three upper front fender bolts located on top of the front fender (16005) inside the engine compartment.
  1. Raise and support the vehicle.
  1. Remove the wheel (1007).
  1. Remove one push pin and five front fender splash shield bolts and remove the front fender splash shield (16102).
  1. Remove the upper front fender brace screw.
  1. Remove the inner front fender bolt.
  1. Remove the screw holding the front bumper cover (17D957) to the front fender.
  1. Remove the two lower front fender bolts.
  1. Remove the front fender.
Installation
To install, reverse the removal procedure. Tighten the front fender bolts to 7-9 Nm (61-86 lb-in).

Feb 24, 2009 | 1999 Mazda 626

1 Answer

Remove power antenna - 96 Seville


If there is a slot in the "fender hole", it unscrews with a big screwdriver If not, check for a slide clip under fender where it goes through.

Jan 17, 2009 | 1996 Cadillac DeVille

1 Answer

Blinker out on '05 CTS


If you are referring to the maker light on the fender you must remove the plastic wheel well liner panel section. from=nt of wheel well to access the light.

Dec 02, 2008 | 2005 Cadillac CTS

Not finding what you are looking for?
2005 Cadillac STS Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...