Question about Nissan Altima

Open Question

Right front wheel bearing on 2004 nissan altima

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

Ad
  • 41 Answers

SOURCE: Steering wheel vibration and whine noise from rear of car

Yes, and it probably is your wheel bearing. Hearing a sound like a chain dragging is classic. You may also hear a clicking noise or chain dragging noise when turning to the left or right.

Look under the car and see if the rubber boots that surround the axle near the tires are cracked and leaking grease. If so, it is almost a certainty that the bearings are bad as you have lost grease and thus lubrication to the bearings.

Good luck,
bob

Posted on May 28, 2009

c17hydro
  • 2984 Answers

SOURCE: Directions replace front wheel bearings on a 1985 nissan stanza?

996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Posted on Jun 23, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2004 silverado 4x4 2500 left front wheel bearing

  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Posted on Jan 19, 2010

  • 409 Answers

SOURCE: replacing front wheel bearings on a 2004 Suburban

The front wheel bearings are sealed units, and must be replaced with the entire hub assembly. They do not need periodic cleaning/replacing as they did in the old days, if they are not making noise do not bother with them.

Posted on Apr 07, 2010

Testimonial: "Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes vibration in front right side near or in the wheel?


vibrations come fro bent shafts , bad wheel bearings out of adjustment bearings, warped disc rotors, faulty tyres ( band shifted ), bulges on side walls, out of balanced tyres

Dec 29, 2013 | 1998 Nissan Altima

1 Answer

I have a 2000 Nissan Altima that is making a clicking noise in the right front tire. My speedometer stopped working for a short time the other day and was wondering if this noise is related to the...


if you still have the clicking noise in right front tire it could be your wheel bearing your speedometer cable goes in your trans. not your wheels

Apr 10, 2013 | 2000 Nissan Altima

2 Answers

Procerure to replace wheel bearing assy 2004 nissan altima 4cyl


Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Sep 19, 2012 | Nissan Altima Cars & Trucks

1 Answer

Rumble in left front wheel on the left front and maybe the right front wheel ther is a rough sound like a dry bearing sound


chances are you are right. if you have just purchased this car, it is possible it was abused if not i would say it is high mileage and you need a professional to inspect it right away before something happens and somebody gets hurt. it also sucks to get towed. these are not hard bearings to replace but you do need the right equipment. you will be alot happier.

Nov 02, 2009 | 2005 Nissan Altima

2 Answers

Have owned 2 2006 altimas and both have had roaring noise like a wheel bearing going out in right rear


It may be caused by a bad wheel bearing. To be sure, try to swap the 4 wheels and see if there would be changes in the noise location. If it does change, the noise may be from the tires that are not worn out evenly.

Sep 27, 2009 | 2006 Nissan Altima

1 Answer

Where is the speed sensor located on 1997 Nissan Altima SE 4 cly.


2004 nissan altima on right front of transaxle near right axle flange1997 nissan altima on transaxle.

Jul 26, 2009 | 2004 Nissan Altima

1 Answer

Steering wheel vibration and whine noise from rear of car


Yes, and it probably is your wheel bearing. Hearing a sound like a chain dragging is classic. You may also hear a clicking noise or chain dragging noise when turning to the left or right.

Look under the car and see if the rubber boots that surround the axle near the tires are cracked and leaking grease. If so, it is almost a certainty that the bearings are bad as you have lost grease and thus lubrication to the bearings.

Good luck,
bob

May 28, 2009 | 2003 Nissan Altima

1 Answer

Where to get at best price a front wheel bearing, altima 2004


thanks, i found this part at: www.car-stuff.com/store

Apr 09, 2009 | 2004 Nissan Altima

2 Answers

Replace font wheel bearing


What exactly is your problem? If you want help you need to give the chassis number and the engine number as well so that I can be specific and give you the right instruction. Cheers

Mar 21, 2009 | Mitsubishi Passenger Cars & Trucks

1 Answer

Where r the wheel bearings on a 2005 nissan altima


you would need to take the wheel off... then the caliper... you will see the shaft that comes thru from the front drive shaft... the bearing is what the shaft goes thru... there should be a cover over it... it's a press fit... you'll need a puller to take it out.

Robert

Jan 17, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...