Question about 1998 Honda CR-V

Open Question

How do you remove broken lug studs on a 1998 honda crv all wheel drive

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: Front wheel stud on 2005 honda civic

U must remove the hub assembly to replace the stud.

Posted on Mar 24, 2009

  • 1596 Answers

SOURCE: broken wheel stud front left 1992 honda accord

Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Posted on Mar 29, 2009

Molson02536
  • 3854 Answers

SOURCE: Need to know how to remove broken studs?

Your going to have to remove the hub bearing unit to replace the studs.
The studs are pressed fit, so your going to have to press it out backwards. Don't try to hamer the studs out, you may damage the Hub bearing and you might as well change the whole hub if that's the case.
Once you have the hub removed press fit the studs out backward and if you don't have a press fit, you could get away with a clamp and lot's of washer and a pipe for leverage. 
To install the new studs, just follow in revers and press fit the new ones in place, it should take about 30 min to an hour to do. But take your time if you have not don this before.
Good luck and hope this helps, and if your have abs, make sure you line up your sensor before putting the wheels back on.

Posted on Apr 19, 2009

slimphilthe1
  • 5 Answers

SOURCE: trying to replace broken lug studs on 1998 honda

you have to drop the balljoints and tie rod ends..essentialy on the 92 the whole brake system.

Posted on Apr 26, 2009

mythman
  • 84 Answers

SOURCE: 1998 honda crv vibrates when starting out

Increased vibration from a vehicle indicates worn out engine supports. This vibration often disappears when revving the engine high, but is very noticeable at low revs.

You can have these inspected and possibly replaced to reduce the vibration cominf from your engine.

Hope this helps.

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW REPLACE LUGS OF RF WHEEL 1998 HHONDA CRV


I think you mean the wheel studs? They are pressed in.You need to remove the wheel,brake caliper and rotor(or drum) and pound the stud out.Grease the new stud,and use HAND TOOLS with a lug nut and a washer(buy a plain open lug nut with one flat side to install it).I have tried using an impact gun to crank 'em in,but usually regret it-the threads strip or the stud breaks.Make sure to keep tightening until the head of the stud sits flush to the back of the flange.If you have difficulty tightening the stud because the axle keeps turning,have someone hold the brake pedal for you.

Oct 07, 2012 | 2004 Hyundai Santa Fe

1 Answer

How do I replace a broken lug nut out of 98 windstar?


you don`t say if its front or rear lug nut(assuming you mean stud).remove the wheel and then the drum or rotor,then take a hammer and hit the broken stud to remove it from the hub assembly.with the correct wheel stud insert it through the hole and make sure its in straight,install the wheel nut and tighten the nut to pull the stud into the hub until all the way in.you may have to install washer on the stud and re-install the nut and tighten until the stud is seated all the way.

Sep 16, 2011 | 1998 Ford Windstar

1 Answer

I have a flat tire, but do not have the special tool to take off the bolt. Any ideas? 2010 Honda CRV


Most auto parts stores have Locking Lug Nut removal tools. If you know the size of your lug nut you may be able to buy a single tool that fits on a standard ratchet to remove the locking lug nut. If your lug nut is the type that spins without the proper tool to remove it, your best bet is a mechanic with the proper equipment to avoid doing damage to the wheel or stud.

Good luck!

Jul 05, 2011 | 2004 Honda CR-V

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

3 Answers

Need to get a wheel lug stud out of the wheel hub. there not enought room to pound it out from the another side it seems to me you have to remove the whole hub? yes or no.?


Dont remove the hub! Usually you can rotate the hub and find a spot that the stud will come out.Other option is to saw off and inch or so of the stud before you remove it.Then knock it out.Good luck!

Apr 20, 2011 | 1998 Chevrolet Monte Carlo

1 Answer

Right side front broaken wheel lug


YOU CAN PRESS OUT BROKEN LUG STUD WITH STUD REMOVAL TOOL AND INSTALL A NEW STUD.THE TIRE SHOP WILL FIX IT.WONT COST THAT MUCH.IF YOU DONT HAVE RIGHT TOOL YOU CAN DAMAGE WHEEL BEARING IF YOU HAMMER ON BROKEN STUD.

Oct 11, 2010 | 1998 Acura RL

1 Answer

Will alloy wheels from a HONDA CRV fit a SUZUKI GRAND VITARA. Both are 5 stud so just wondering if anyone can help


The rims from the Honda CRV won't fit the Grand Vitara.

The Honda has a 5 X 114.3mm spacing and the Grand Vitara has 5 X 139.7mm spacing. This means that even though they are both 5 lug rims, the Honda lugs are spaced closer together than the Vitara so they won't match up.

Nov 07, 2009 | 2001 Suzuki Grand Vitara

1 Answer

Does the wheel barring have to be replaced when the stud is broke


If you use a hammer to drive the broken stud out you can cause damage to the bearing.
If you use a wheel stud press, the hub bearing will not be affected. The press will remove the old stud and install the new one.
Good luck.
Regards,

Aug 18, 2009 | Honda Civic Cars & Trucks

2 Answers

Broken wheel stud front left 1992 honda accord


Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Mar 29, 2009 | 1992 Honda Accord

1 Answer

Front wheel stud on 2005 honda civic


U must remove the hub assembly to replace the stud.

Mar 24, 2009 | 2005 Honda Civic

Not finding what you are looking for?
1998 Honda CR-V Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...