Question about 1988 Toyota Camry

1 Answer

'88 toyota camry rear window stuck in down position

I have a 1988 toyota camry with power windows and the rear driver's side window is stuck in the down position. i have tried lots of thing to no avail -- i believe my next viable option is to take the door panel off and manually crank the window back up. i'm wondering if anyone can tell me the proper way to take the door panel off and do this procedure or if there are any other ideas.

Posted by on

  • detmarjohn Apr 28, 2009

    i need to replace the front driver side window motor, are the directions the same as in this post?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Diagram for 1988 Toyota camry power window switch


I have the same issue, I can't find anything online for the location of the power window relay or the circuit for the power windows.on a 1988 Camry. Either the internet is lame or the 1988 Camry is truly bullet proof, where there are no people that ever had the same problem where it would be posted online and we could find it with ease

Aug 07, 2011 | 1988 Toyota Camry

1 Answer

I have a 1994 Toyota Camry and the power window on the passenger side has gone down, under power. Then nothing would happen when I would pulled up on the switch on the driver side main switch and the also...


more than likely one of the switches are bad (down side of switch works but up side of switch dont) being as the switches are wired together if one goes bad other one won't work either take the switch out one of back doors should be same as front passenger door put rear switch in front passenger door if works then u know front door switch is bad if it doesn't then drivers door switch is bad
u replaced window regulator Did that come with motor too??? if not check to see if motor is good
there is two wires going to motor cut isolation back on wires and using some jumper wires attach one wire to positive terminal of a 12 volt battery attach other wire to negative terminal of battery window should move up or down reverse connections and window should move other way

Jan 29, 2011 | 1994 Toyota Camry

1 Answer

88 Toyota Camry... windows wont let up.i checked fuse box on drivers side, none were blown, so i bought a used one... still not working.


poss window motor is shorted out or have abroken wire do u hear ur window motor working? if not hten u have a bad window motor

Apr 04, 2010 | 1988 Toyota Camry

1 Answer

91 Camry Seat belt and power winodws on Passenger side Inop


More than likely, you have a broken wire or two between the body and the driver side front door. This is a very common issue with those cars when tey get older.

Oct 09, 2009 | 1991 Toyota Camry

3 Answers

'88 Camry Power Windows and Locks Won't Work


at the drivers side panel there are 2 relays with metal tops on them.Push the little holes on top of the with a paper clip and reset them.This may help

May 26, 2009 | 1988 Toyota Camry

2 Answers

Divers window won't roll up my Camry


No won't be fuse. My guess is there is something faulty with the main controller. You could probably verify this by trying the switch on right rear passenger door. If it works there then the problem is at the main controller in the driver door. Could be a loose wire or the switch itself is broken.

May 13, 2009 | 1986 Toyota Camry

1 Answer

'88 toyota camry rear window stuck in down position


have you tried to remove the doors window switch and ensure that you have a good 12 volts at the switch? I assume when you said you've tried everything that meant you checked the fuses. You can check with a voltmeter but a test light will actually ensure good voltage.

Jan 22, 2009 | 1988 Cadillac Sedan DeVille

1 Answer

Power Window problem, 1998 Toyota Avalong xls


the window motor basically the set up dat make it go up and down behind the door

Dec 29, 2008 | 1998 Toyota Camry

1 Answer

Trying to remove driver side interior door panel on '88 Toyota PU


There is a cotter pin in the window crank, a pair of needle nosed pliers should be able to grab it

Dec 02, 2008 | 1988 Toyota Pickup

Not finding what you are looking for?
1988 Toyota Camry Logo

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...