Question about 2003 Ford Escape

Open Question

Running board removal - 2003 Ford Escape

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the running board?


All running boards are mounted to the underside of the vehicle on newer models. Remove the bolts that hold the running board brackets to the underside of the vehicle and they should come right off. On older vehicles there may be bolts in the wheel wells holding them also

Apr 25, 2015 | Cars & Trucks

1 Answer

Where is the horn location under hood of a 2007 mercury mountneer?


Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation
  1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
    • To install, tighten to 23 Nm (17 lb-ft).
  1. Remove the lower pin-type retainer from the front fender moulding.
  1. Remove the 2 rear pin-type retainers from the front fender moulding.
  1. Position the front fender moulding aside and remove the splash shield lower screw.
    >
  1. Remove the front splash shield screws.
  1. Remove the front splash shield pin-type retainers.
  1. Remove the front splash shield.
  1. Remove the front fender splash shield.
  1. To install, reverse the removal procedure.

Mar 25, 2015 | 2007 Mercury Mountaineer

1 Answer

How to remove power running boards on a 2007 cadillac escalade esv


You are better off Getting some Mechanic Wire and removing the 8 bolts holding the Front of the Running Boards and having it repaired or replaced. I would recommend not using the Running board on that side, you can do that by Climbing under and disconnecting the Plug to the Motor. I would also put a BAG over the 2 connectors and protect them. You can even put a dielectric to keep the Water Out.... Order the Bracket and install the new one at the same time... SAve you time and Effort.

Apr 05, 2013 | 2007 Cadillac Escalade Ext

1 Answer

Retractable running board not functioning


Remove the running board and pry down the bracket holding the board to the motor. (I used a crow-bar) This will rotate the mechanism slightly and the board should work again. I did this a few months ago because the board on the driver side stopped moving. It has been fine ever since.

Apr 19, 2012 | 2009 GMC Yukon Denali

1 Answer

Not sure where fuel filter is


it is located under the driver running board...,just raise the car and remove the lower batwing cover..you will see two ten mm bolts on both sides of the running board,then you will see 2 eight mm bolts,then three 10 mm bolts near the front. ..once its removed you will see the fuel suply line running upward where the drivers foot rest incline is and the fuel filter is just past the incline..make sure you remove the fuse in the trunk for the pump to depressurize it...good luck and let me know if you need any more help.

Sep 21, 2011 | 2005 Jaguar Vanden Plas

1 Answer

My Mercedes ML 430 drivers electric window has stopped working Im tolld that it is elecrical board under the control buttons needs replacing how do I do this


It can be the board or it can be the switch or the mechanical regulator in the door. The switches are all connected in the center console. First remove the gear surround plastic, it should just pull out. Remove the front cubby area liner so as not to lose anything as you remove the wood trim. Remove the ash tray. Wood trim should pull out and you should see the switch assembly. Try removing that switch from that winow and switching it with another switch on the board and try. Sometimes the switch itself goes bad. If not replace the board. Runs around 150 dollars from the dealer. If that doesnt work the regulator is accessed from removing the door panel.

Good luck.

Aug 01, 2011 | Mercedes-Benz ML350 Cars & Trucks

1 Answer

Running board light bulb replacement in 1998 Ford


on the bottom of the running board there is a flap with a phillips head screw in it that covers the bulb socket. just remove the screw and turn the buld socket to remove bulb and replace with the new bulb

Apr 03, 2009 | 1998 Ford Expedition

1 Answer

Can't remove bolts to mount running boards


Do u or any friends have an air compressor? If u can borrow an impact gun the bolts will come right off. I've had an air compressor for years, purchased an impact driver, can't believe how easy it removes bolts I can't budge. U may be able to rent a portable compressor and impact gun. Hope this helps, good luck, and let me know how it comes out.

Dec 28, 2008 | 2007 Ford Ranger FX4 Off-Road

2 Answers

Power running board failure


This is not really solving the problem, but my dealer told me that they could unplug the harness to keep the running boards in the down postion. The running boards have to be in the down position to make this happen.

Nov 18, 2008 | 2003 Mercury Mountaineer

2 Answers

Wiper Motor


Yeah I too had the same problem and its' the board...
age, moisture on board so spend about 15-25 bucks at the dealer and ....let it rain!!!

Aug 02, 2008 | 1992 Chevrolet K1500

Not finding what you are looking for?
2003 Ford Escape Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...