Question about 1999 Pontiac Grand Prix

Open Question

Socket size for 1999 grand am axle nut - 1999 Pontiac Grand Prix

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wireguy212
  • 1627 Answers

SOURCE: what size is the nut on the cv axle

G.M. uses a metric nut,you need a 30mm socket.

Posted on Oct 19, 2009

wireguy212
  • 1627 Answers

SOURCE: size of socket ineed for a axle nut on 1999

You need a 30mm socket,the nut should come almost off before you even lift the car off the ground[unless you have a good air impact driver].

Posted on Jan 16, 2010

  • 1453 Answers

SOURCE: What size socket do I need to remove the front

If you're trying to loosen the large axle nut, in the center of the rotor, it's either a 32mm or a 36mm socket.

Posted on Feb 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size is the axle nut on a 97 jeep grand cherokee 4X4 5.2? Also what size are the E-torx on the back side of the hub?


my socket set goes to 1-1/4": and 36mm.
my e-torx kit has all sizes, one can need.
with no sets. you must measure them. it's not covered in the FSM.
only 175ft/lbs on the axle nut and need for a torque wrench that big.
kit 1:
http://www.sears.com/titan-tools-13-pc-e-torx-socket-set/p-00926107000P?sid=IDx01192011x000001&kpid=00926107000&kispla=00926107000P

the better question is ,is the axle nut SAE or metric.
most real Chrysler built are metric.
so that big nut, at that torque needs 1/2' drive
and the torque wrench to match.
id bet this covers that
http://www.harborfreight.com/13-piece-12-drive-metric-deep-wall-impact-socket-set-67904.html

you could off the hub cap and measure the nut, with a metric rule.
the external torx same. with a caliper measure the head.
then use the e-torx table to mach it.
bet the first ever to post that. its rare to ask.
most folks just have the 2 sets. ( a life time investment if ever there was)
here is the table i uses, if ever
http://en.wikipedia.org/wiki/Torx

good luck working with only 2 bits.

May 03, 2014 | 1997 Jeep Grand Cherokee

1 Answer

Front axle nuts size for 2003 pontiac grand prix


2002 Grand Prix front axel nut holding on hub is a 33MM or 1 5/16 deep socket

Feb 08, 2012 | 2003 Pontiac Grand Prix

1 Answer

On a 1989 cadillac sedan deville what size is the socket to take the axle nut and what is the lenght of the socket


85-91 is 36mm for front axle nut. its just a standard axle nut socket. good-day! but the auto parts store will tell you the size if you buy one there.

Jan 13, 2012 | 1989 Cadillac Sedan DeVille

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

What size socket do I need to remove the front wheel spindle nut from a 2000 pontiac grand prix


If you're trying to loosen the large axle nut, in the center of the rotor, it's either a 32mm or a 36mm socket.

Feb 24, 2011 | 2000 Pontiac Grand Prix

1 Answer

What size is the axle hub nut on a 1999 chev venture


I,d say a 3/4 inch nut,size.You can look at the lug wrench randle socket, and measure it with a tape measureing tape, from a flat to another flat in the socket and get really close.Or take it to a parts supply store and they will check it for you.

Sep 18, 2010 | 1999 Chevrolet Venture

1 Answer

Front wheel bearing assembly unit, what tools will i need? size sockets ext the right foot lbs of torque for the axel nut,


TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Mar 16, 2010 | 1999 Oldsmobile Alero

2 Answers

Axle nut size on 1999 chevrolet Malibu


i just did a 2000 malibu which is the same thing and its not a 32mm. its a 36mm deepwell socket. dont use a regular socket as it wont be deep enough. buy a 36mm deepwell socket for $17 and use a cheater bar and youll be good to go.

Jan 17, 2010 | 1999 Chevrolet Malibu

1 Answer

How do I remove and replace the front axle?


you first need to remove the big nut that is holding the wheel on the side that you are trying to replace first you must buy the right sized socket thet will fit the nut the while the vehicle is still on the ground take the hub cap off and the cater pin out and then put the socket on the nut using a halt inch tourge ratchet loosen and remove the nut then jack your vehicle up and remove the wheel and the bolts that are holdung the hub and then with a pickle fork that is the tool used for removing tie rod ends that is connected to your stirring and then after that remove your axle and then reverse the procces to put ti back together.

Sep 10, 2009 | 2000 Suzuki Grand Vitara

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...