Question about 2001 Chevrolet S-10

Open Question

HOW TO REMOVE AIR INTAKE COVER ON 2001 S10 4.3L?

CANNOT SEE WING NUT ON AIRTAKE, AND DO NOT UNDERSTAND HOW IT IS ATTACHED AT REAR?

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: Just curious on my 2001 cavalier base model are my

The black lug nuts are the lug nut cover that you have to unscrew off the lug nut it self to remove the wheel cover. Once the wheel cove is off you'll see the real lug nuts holding the wheel in place, note do not over torque the plastic lug nut cover when re installing the wheel cover. The plastics are know to crack and will not hold the wheel cover on the wheel any more cause you to lose them on the hy way. Good luck and be safe, oh and the plastic lug nut cover is attached to the wheel cover so do not try to separate them from the wheel cover. 

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 buick park ave replace air filter


Dave, Under the cover is he air filter, If wing nut are seized or broke, soak threaded areas of these fasteners with a penetrating oil, a few times over a day. You may have to use pliers/vise grips if wing nut is damaged. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Under Hood Bath GM Forum Buick Cadillac Chev Olds GMC Pontiac chat
How to Remove Rusted Bolts
How To Remove Rusted Screws Nuts Bolts In 10 Easy Steps

Jul 31, 2016 | Cars & Trucks

1 Answer

Need to remove valve cover on 2000 Camry Toyota


For the four cylinder engine:

  1. Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.
  2. Remove the spark plug wires. Disconnect the PCV hose.
  3. Remove the four nuts and grommets located on top of the cylinder head cover.
  1. Remove the cylinder head cover and the cover gasket from the cylinder head.
  2. Discard the gasket and replace with a new one.
To install:
  1. With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.
  2. When the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustrations.
  3. Install the new cylinder head gasket in the cover. Make sure that the gasket seats evenly.
  4. Place the cylinder head cover with the gasket onto the cylinder head.
  5. Install the four grommets and nuts. Uniformly tighten the nuts in several passes to 17 ft. lbs. (23 Nm).
  6. Connect the PCV hose. Connect all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.
  7. Start the engine and inspect for oil leaks.
  8. Repair any leaks as necessary.
For the V-6 (3.0L) engine:
  1. Drain and recycle the engine coolant.
  2. Disconnect the radiator inlet hose.
  3. Disconnect the throttle and accelerator cables.
  4. Remove the air cleaner cap assembly.
  5. Remove the V-bank cover. Use a hexagon wrench to loosen the nuts.
  6. Label and remove all emission control valve hoses. Disconnect any wiring interfering with the valve cover removal.
  7. Remove the air intake chamber. This will gain you access to the back valve cover.
  8. Disconnect the engine wire from the left hand side, No. 3 timing belt cover, rear side and right hand side. Most of the wiring is secured by nuts and or bolts to the body of the vehicle.
  9. Remove the ignition coils, make sure the place them in order on a table so not to mix them up.
  10. Remove the 8 bolts retaining the valve covers and gasket.
  11. Clean the mating area of the valve cover and cylinder heads well. If necessary, scrape any left gasket from either surface.
  12. Apply seal packing to the cylinder heads and place new gaskets into position.
  13. Attach the valve covers. Uniformly tighten the bolts in several passes to 69 inch lbs. (8 Nm).
  14. Install the spark plugs in their proper locations, then place the ignition coils into place and secure.
  15. Attach all engine wiring be sure to secure each harness properly.
  16. Install the air intake chamber. Refer to Fuel System .
  17. Attach all emission hoses and wiring.
  18. Attach the V-bank cover.

Apr 15, 2014 | 2000 Toyota Camry

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

How do you replace a 2001 Hyundai Elantra thermostat?


Remove the air cleaner. Drain coolant. Standing in front of the vehicle, the right side of the engie (across from the air cleaner) you'll see a black cover attached to the side of the upper engine. Slowly pull off (its attached with plastic snaps-just pull). Where the black cover attached you should see 2 nuts securing the thermostat housing. Remove nuts and washers, and thermostat housing (I believe they're 12mm). Remove thermostat and gasket. Install thermostat first the same way it was removed. Install gasket (may need to use gasket sealer to hold it in place). Install washers and nuts and hane tighten then 1/8-1/4 turn.

Aug 30, 2011 | 2001 Hyundai Elantra

1 Answer

Starter needs to be replaced. Need instruction procedure for a do it yourselfer.


Hi, I have pasted the procedure from autozone.com below. Because this requires removal of the intake manifold, please be as sure as possible that your starter needs replacement. If you have any doubt, please let me know what your symptoms are and what troubleshooting you have done that led you to believe your starter is bad. Also, if you have any questions about the procedure below, please let me know. Thanks for using FixYa.


Removal & Installation


Disconnect the Negative battery cable


Relieve the fuel system pressure (you can do this by placing a rag over the schrader valve on the fuel rail and pressing in the valve stem--just be careful not to spray fuel on your eyes).


Drain the cooling system.


Remove or disconnect the following:


  • Intake manifold heat shield
  • Sight shield
  • Coil module connectors from the coil modules located on the valve covers
  • Positive Crankcase Ventilation (PCV) hose and valve from the valve cover
  • Fuel regulator vacuum tube
  • Vacuum tubes from the AIR solenoid
  • Fuel inlet and return lines
  • Fuel rail bracket retaining nut at the rear lift bracket
  • 2 pushnuts attaching the engine coolant heater wire and set it aside, if equipped
  • Fuel injector electrical connections
  • Fuel rail and injectors
  • Plenum duct clamp at the rear of the intake manifold, loosen
  • Intake manifold bolts and the manifold
Clean the manifold mating surfaces.


Remove or disconnect the following:
Starter electrical connectors Starter motor

jturcotte_1382.gif


Fig. View of starter motor removal and wires



To install:

Install or connect the following:

  • -S- terminal wire. Torque the nut to 35 inch lbs. (4 Nm).
  • Starter electrical connectors. Torque the nut to 89 inch lbs. (10 Nm).
  • Starter motor
  • Mounting bolts. Torque the bolts to 22 ft. lbs. (30 Nm).


jturcotte_1383.gif


Fig. Intake manifold torque sequence- 4.6L engines

  1. Grease the inside edge of the rubber plenum duct.
  2. Position the intake manifold by performing the following sub-steps:
    1. Place the rear of the intake manifold into the plenum duct.
    2. Place the front of the intake manifold downward on to the cylinder heads.

  3. Install the intake manifold bolts and torque to 89 inch lbs. (10 Nm) in the sequence illustrated. DO NOT torque the intake manifold bolts when the engine is HOT or at operating temperature.
  4. Make sure the plenum duct is fully attached to the rear of the intake manifold and tighten the plenum duct clamp to 20 inch lbs. (2.25 Nm).
  5. Install or connect the following:

    Fuel rail and injectors and tighten the rail retainers to 89 inch lbs. (10 Nm) Fuel injector electrical connections Alternator coolant pipe/surge tank pipe and position onto the fuel rail studs Engine coolant heater wire onto the studs and install the pushnuts, if equipped Fuel rail bracket retaining nut at the rear lift bracket and tighten to 89 inch lbs. (10 Nm) Fuel inlet and return lines Vacuum tubes to the AIR solenoid Fuel regulator vacuum tube Positive Crankcase Ventilation (PCV) valve and hose to the valve cover Coil module connectors to the coil modules located on the valve covers Sight shield Intake manifold heat shield Negative battery cable
  6. Fill and bleed the cooling system.

Mar 31, 2011 | 2002 Cadillac Deville

1 Answer

Need to replace rear brake light just pull hard and the bulb will come out of the hole


Please don't forget to rate! Thanks!

  1. Disconnect the negative battery cable.
  2. Remove wing-nuts attaching tail lamp to rear closure panel.
  3. Remove lamp from opening in quarter panel.
  4. Disconnect wire connector from back of tail lamp.
  5. Remove tail lamp from vehicle.
  6. To install, reverse removal procedure.

c17hydro_125.gif

Locating wing nuts (2) in the trunk (1)



c17hydro_126.gif

Removing taillight (1) and connector (2)



c17hydro_127.gif

Identifying taillight components

Jan 22, 2011 | 2000 Plymouth Breeze

1 Answer

Where is the air intake located???? on my 1996 Blazer???


There is the air box on the drivers side frort corner has 4 plastic wing nuts on top. Then the air duct goses to the mass air flow senser from there it goes to the top center of the engine that is the intake for all air to the throttle body it also has a plastic wing nut but its 4 inches long remove that and slide the plastic cover forward and ti comes off and you can see the throttle plate.And im assumeing you have a 4.3 vortec engine.

Dec 28, 2010 | Chevrolet Blazer Cars & Trucks

4 Answers

My starter gave out yesterday. I didnt know it was inside the intake manifold. Either way i started the job last night, i am having a hard time pulling out the manifold. I already loosened the clamp but i...


Hi!!
These are the steps to follow to remove the Starter Motor and the Intake Manifold. If you follow them you'll have no problems when the job is done. Pay special attention to the pre-installation steps for the Intake Manifold.

To Replace the Starter, Remove or disconnect the following:
  1. Negative battery cable
  2. Intake manifold
  3. Starter electrical connectors
  4. Starter motor
View of starter motor removal and wires
1kbron_11.jpg

To install, Install or connect the following:
  1. -S- terminal wire. Torque the nut to 35 inch lbs. (4 Nm).
  2. Starter electrical connectors. Torque the nut to 89 inch lbs. (10 Nm).
  3. Starter motor
  4. Mounting bolts. Torque the bolts to 22 ft. lbs. (30 Nm).
  5. Intake manifold
  6. Negative battery cable

INTAKE MANIFOLD
PRIOR TO REMOVAL:
  • Relieve the fuel system pressure
  • Drain the cooling system.

Remove or disconnect the following:
  1. Negative battery cable
  2. Intake manifold heat shield
  3. Sight shield
  4. Coil module connectors from the coil modules located on the valve covers
  5. Positive Crankcase Ventilation (PCV) hose and valve from the valve cover
  6. Fuel regulator vacuum tube
  7. Vacuum tubes from the AIR solenoid
  8. Fuel inlet and return lines
  9. Fuel rail bracket retaining nut at the rear lift bracket
  10. 2 pushnuts attaching the engine coolant heater wire and set it aside, if equipped
  11. Fuel injector electrical connections
  12. Fuel rail and injectors
  13. Plenum duct clamp at the rear of the intake manifold, loosen Intake manifold bolts and the manifold
  14. Clean the manifold mating surfaces.
Intake manifold torque sequence- 4.6L engines

1kbron_12.jpg


PRIOR TO INSTALL:
  • Grease the inside edge of the rubber plenum duct.
  • Position the intake manifold by performing the following sub-steps:
  • Place the rear of the intake manifold into the plenum duct.
  • Place the front of the intake manifold downward on to the cylinder heads.
  • Install the intake manifold bolts and torque to 89 inch lbs. (10 Nm) in the sequence illustrated. DO NOT torque the intake manifold bolts when the engine is HOT or at operating temperature.
  • Make sure the plenum duct is fully attached to the rear of the intake manifold and tighten the plenum duct clamp to 20 inch lbs. (2.25 Nm).

Install or connect the following:
  1. Fuel rail and injectors and tighten the rail retainers to 89 inch lbs. (10 Nm)
  2. Fuel injector electrical connections
  3. Alternator coolant pipe/surge tank pipe and position onto the fuel rail studs
  4. Engine coolant heater wire onto the studs and install the pushnuts, if equipped
  5. Fuel rail bracket retaining nut at the rear lift bracket and tighten to 89 inch lbs. (10 Nm)
  6. Fuel inlet and return lines
  7. Vacuum tubes to the AIR solenoid
  8. Fuel regulator vacuum tube
  9. Positive Crankcase Ventilation (PCV) valve and hose to the valve cover
  10. Coil module connectors to the coil modules located on the valve covers
  11. Sight shield
  12. Intake manifold heat shield
  13. Negative battery cable
  14. Fill and bleed the cooling system.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Nov 11, 2010 | 2001 Cadillac DeVille

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

1 Answer

How do I change front blinker bulb on 2003 chev impala


First,
  1. Turn the engine off and open the hood. Pry up the two fasteners from the radiator air baffle with a flat head screwdriver. Move the baffle to the side to access the top of the headlight case.
  2. Step 2 Pull up the two metal rods behind the headlight case. These secure the case to the car. You may need your pliers to pull them up.
  3. Step 3 Gently pull the headlight case out to access its rear. On the rear, you will find several black dust covers. Twist off the dust cover closest to the fender (the outward dust cover) to access the turn signal bulb.
  4. Step 4 Turn the bulb module counterclockwise to release it. Unplug the electrical connector from the bulb module. Connect the new bulb to the electrical connector (don't touch the glass with your hands; hold it by the plastic piece). Insert the bulb module in the turn signal housing, turn it clockwise and screw the dust cover back on.
  5. Step 5 Insert the headlight case in the mount. Push the pins back down to secure it. Position the radiator baffle in its place and insert the fasteners.
  6. Rear Turn Signal Bulbs
  7. Step 1 Open the trunk. Remove the net from the side mounted wing nut (on the side with the faulty turn signal). Twist the wing nuts (there are two per side) counterclockwise to remove them.
  8. Step 2 Peel the carpet layer back to access the rear signal lamp wing nuts. Twist these wing nuts (two per side) counterclockwise to remove them and release the rear signal.
  9. Step 3 Carefully pull the rear signal assembly away from the Impala. The rear turn signal is the inner bulb (closest to the trunk). Press the tab on the bulb module and turn it counterclockwise to release it from the rear signal assembly.
  10. Step 4 Pull the old bulb straight off the module (don't twist). Insert the new bulb in the module. Depress the tab on the connection and insert the module back in the assembly. Twist it clockwise.
  11. Step 5 Insert the rear signal assembly. Re-attach the assembly's wing nuts and push the carpet layer back in place. Tighten the other two wing nuts to secure the carpet layer and reconnect the cargo net

May 09, 2010 | 2003 Chevrolet Impala

Not finding what you are looking for?
2001 Chevrolet S-10 Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...