Question about 1997 Isuzu Rodeo

1 Answer

The clutch pedal sticks and the car wont go into gear. Could the clutch fluid be low or could it be more serious?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

You might have a bad slave valve, have it checked, and check the fluid anyway.

Posted on Jan 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My clutch is going straight to the floor and car wont go into gear


But check in see if it's just the ball joints first that's a easy fix compared to replacing the whole clutch I have a 1999 Ford escort manual and just had this problem I know all I need to know about this car make and model trust me it's your clutch nothing else You are soon to run into belt problems too keep an eye on that

Mar 29, 2014 | 1999 Ford Escort

1 Answer

Car wont move when in drive gear


either low on fluid or forard clutches are out..

Dec 30, 2013 | Toyota Passenger Cars & Trucks

1 Answer

Started off with cluth sticking to floor.would have to pull clutch pedal back up with foot. truck would stick in gear. even with clutch fully depressed. seemed like spring had disconnected from clutch...


your clutch uses a hydraulic master and slave cylinder to disengage. It is likely that the slave has been leaking and the reservoir gone dry, thus allowing air into the system and reducing effectiveness. Check the clutch master cylinder reservoir (near the brake reservoir) fluid level. If low, also check the slave cylinder at the clutch for leakage. If leaking, replace the slave and bleed the system. If you need procedures or have more questions, please let us know.

Sep 25, 2010 | 1994 Nissan Pickup

2 Answers

Clutch pedal sticks to the floor; the brake reservoir was low


I believe your pressure plate is broken and at a minimum will have to be replaced along with the clutch disk.

Jul 04, 2010 | 2006 Ford Fusion

1 Answer

Clutch Dodge SX2.0 2004


Just to be sure recheck the fluid level of the mastercylinder again. If it is a little low refill with proper fluid, and work the clutch several times with parking brake set. Also check the clutch pedal bushings at the top of clutch pedal to make sure there is no sticking or excessive wear. If you find anything unusal about the bushings, they need to be replaced. Hope this will help you.

May 16, 2010 | 2004 Dodge Neon

2 Answers

1989 jeep wrangler wont shift gear and clutch gone loose


Get the clutch slave cylinder and master cylinder looked at.One of the 2 has failed.If the pedal goes to the floor or is very loose,this is very likely the cause.Not an expensive fix.Hope this helps

Jan 10, 2010 | 1989 Jeep Wrangler

1 Answer

Clutch sticks when pushed to floor


a clutch pedal that doesn't return back to you is sometimes a symptom of a failing clutch slave or general fluid leak. This is of course referring to a hydraulic clutch. If your fluid gets too low or there is an air leak your pedal will stick to the floor and not return.

Oct 26, 2009 | 1994 BMW 3 Series

3 Answers

Pedal is going to the floor and hard to put into gear.


you mean the clutch pedal? when asking questions it helps to tell which engine, trans, 4wd, 2wd, which pedal, what you have checked, ect......... ck the clutch fluid level ,you will need to replace the clutch master and slave cylinder, the trans will have to come out.

Oct 19, 2009 | 2007 Mazda B3000

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

1 Answer

Clutch wont work


Check and make sure you have fluid in the clutch master cylinder. If it is low fill and check for leaks. Repair leaks as needed and bleed system. If fluid was full check adjustment and bleed system, if there is air in the system pedal will go to the floor.

Oct 02, 2009 | 1991 Mitsubishi Eclipse

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...