Question about 1999 Toyota Corolla
What would cause all these codes to come in at the same time
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
These codes are all for the Evaporative Emissions System.
P0440- Evaporative emissions system fault- just saying there's something wrong with the system.
P0441- Evaporative emissions system- Incorrect purge flow- saying that the system isn't purging the raw fuel vapors (hydrocarbons- HC) as well as it should.
P0446- Evaporative emissions system- Control valve circuit low- there is a valve, usually located on the charcoal canister at the rear of the vehicle, that opens to allow fresh air to enter the evaporative emissions system as the engine vacuum purges the fuel vapors from the charcoal canister and closes when purge is not needed to prevent leakage of those fuel vapors to the atmosphere (HC is a greenhouse gas and is regulated as such by the fed gov't).
Given that you have the incorrect purge flow code and the control valve code together, my bet is that the vent control valve has failed (causing the P0446) and is not opening to allow fresh air into the system to displace the air from within the system that is being pulled to the engine. Since you have no fresh air entering the system, the engine will pull a vacuum on the system instead of the vapors "flowing" into the engine (causing the P0441).
I hope that this is helpful to you!!!
ASE Master Technician with L1 and X1 Certifications; Nissan Scope Technician; Chrysler Level 3 Silver Technician- 12+ years experience.
Posted on Nov 17, 2008
p0441 - Evaporative emission control system Incorrect purge flow. can be caused by a lot of things and is usually related to a small leak in the emission control evap system, try replacing the gas cap and see if it helps, if not, the system needs to be tested for a leak with the scantool or a leak tester or both.
usually you will see p0440 p0441 and p0446 together but before anything replace your gas cap and besure to tighten it down when you gas up the vehicle, 90% of the time with those codes either a loose gas cap of bad gas cap gasket is the problem
Otherwise - Might be a canister leak, defective VSV valve or hoses, bad gascap seal.
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.
Posted on Mar 17, 2009
Everything that I could find on this made it seem like it might be your charcoal cannister. Check this out and it should help you out:
Posted on May 17, 2009
Both codes are with the EVAP SYSTEM, there are numerous items it could be. A repair shop that does Toyotas or the delaler would be the best to check it out for you. Its not anything that will leave you walking or disable the car.
Posted on Nov 13, 2009
Tips for a great answer:
Feb 21, 2016 | 2003 Lexus LS 430
Feb 03, 2014 | Cars & Trucks
Jan 13, 2013 | Cars & Trucks
Jun 18, 2017 | 2004 Pontiac Grand Prix
Repair open or short in voltage feed circuit to Purge Solenoid.
Repair open in PCM purge command circuit.
Replace purge Solenoid.
Replace vacuum switch.
Repair restriction in Evap line or canister or soleniod.
Repair resistance in purge connector.
Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
Otherwise, replace the gas cap, or
Inspect the EVAP system for cuts/holes in tubes/hoses.
Aug 15, 2011 | 2003 Toyota ECHO
Apr 23, 2011 | 2008 GMC Envoy
Feb 06, 2010 | 1997 BMW 328
188 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: