Question about Chevrolet Cars & Trucks

Open Question

What size allen wrench is used to remove fill plug on the transmission on a chevy 1990 cheyne

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1055 Answers

SOURCE: allen wrench size to fit caliper mounting bolt

some are 7/16 and some are 3/8 amd some are torx

Posted on May 30, 2009

  • 2 Answers

SOURCE: bolt size for 96 chevy front caliper

2002 Trailblazer - 4 bolts on caliper. I loosened the top bolt with the pin, but when I try to loosen the bottom, it feels like I'm tightening it. Do I need to loosen all 4?

Posted on Jul 16, 2009

  • 297 Answers

SOURCE: 2005 grand caravan ? size allen wrench to remove rear calipers

6 mm to small 8 mm to big, how about 7 mm would you not think ??

Posted on Aug 16, 2009

  • 1 Answer

SOURCE: removing filler plug from transfer case

On an 02 Santa Fe the Transfer Case Filler plug requites a 10mm allen wrench. A socket type works best.

Posted on Sep 18, 2009

  • 14036 Answers

SOURCE: what size allen wrench is needed for 2006 jeep


Posted on Sep 17, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What size allen wrench would I need to take off the calipers on my 1990 Buick LeSabre front brakes

I use a set of allen type drivers on a 3/8 drive breaker bar or ratchet. Most parts stores sell a set of 5 or 6 sizes.

Jun 15, 2015 | 1990 Buick LeSabre

1 Answer

Vw t25 gearbox oil change

You will need a very large allen wrench (like 19mm or so) for the drain and fill plugs.
This is an uncommon size so if you do not want to invest in one just have a shop do it.
If you decide to go ahead, get GL-4 hydraulic oil and a pump. Remove fill plug first (to ensure you can before draining transmission!) on side of transmission, about mid-line.
Then remove drain plug (center bottom toward engine). Have catch pan ready.
Once it has all dripped out, replace drain plug and fill with pump through side plug until it starts to drip back out (car level).
Let it finish dripping out, replace plug and good to go!

Jan 20, 2013 | 1986 Volkswagen Wagon Camper

1 Answer

Where do i put the gearbox oil on the chev lumina ss 2008

If it's a manual transmission then there should be a check plug on the side of the transmission. It should have a 4 sided plug you can remove with eather a 15 or 16 mm open-end wrench or an adjustable (crescent) wrench. Don't overfill, but keep it within 1 inch of the bottom of the check plug hole. Carefully use an allen wrench to check. If the vehicle has an automatic transmission and it has a transmission dipstick, then you can fill it through the dipstick tube but again do not overfill. Drive after filling and with the oil warm ensure the oil level is within the warm/hot cross hatches on the dipstick. Do not overfill. If there is no transmission dipstick on the automatic, then take it to your dealership to fill.

Dec 18, 2012 | Chrysler Town and Country Cars & Trucks

1 Answer

How to check transmission fluid in manual transmission

The transmission case has a lower drain plug and an upper fill plug on the side of the transmission case. You need a special 17mm Allen wrench to remove the drain and fill plugs on the ******.Open the upper fill plug and add the specified GM ****** fluid till it dribbles out the fill plug hole.

Oct 14, 2012 | 1998 Chevrolet Chevrolet silverado

1 Answer

What fluid does a 1997 chevy C1500 5 speed manual trans. use

Do you people even read before you answer! There is no park on a manual tranny! The axles do not go into side of transmission either. on this TRUCK aka C1500... This is a truck not a fwd automatic car.If you dont know then dont answer questions!Flat ground take top plug on side of tranny out and fill till it comes back out with 75w90 or 80w140(depending hot/cold climate)You will need a Special removal tool(huge allen wrench type for the drain and fill plugs on right/passenger side of tranny)

Jun 29, 2012 | GMC Sierra Cars & Trucks

1 Answer

How do you check the transfer case fluid level

  • Locate the fill plug in the center of the transfer case facing the rear. The fill plug is a hex head bolt.

  • Remove the fill plug and check the fluid level. Insert the short end of an L-shaped Allen wrench into the hole. Spin the Allen wrench slightly and remove it. Some fluid should be present on the tip if the unit is full.

  • Attach a screw-on hand pump to a bottle of Mopar ATF+4 type 9602 automatic transmission fluid. Insert the other end of the tubing for the hand pump into the fill plug hole on the transfer case.

  • Pump fluid into the transfer case until the fluid is flush with the bottom of the hole. A small bead of fluid will drip out of the hole when the case is full.

  • Reinstall the fill plug and torque it to between 15 and 25 foot-pounds of torque. Hand-tightening the plug and turning it 1/2-half turn further with a socket wrench is equivalent to 20 foot-pounds of torque if you do not have a torque wrench available.

  • Mar 01, 2011 | 2002 Jeep Liberty

    1 Answer

    Is it true that there is no dipstick?

    No such thing as "dipstick" on the Freelander.
    Filler plug is located on top of the transmission next to two electrical connectors.
    Level plug is located on the bottom of the transmission, next to the selector cable.
    Use 5mm allen wrench to remove it, and fill the transmission fluid till it starts dripping from the level plug.

    Oct 07, 2010 | 2002 Land Rover Freelander

    1 Answer

    What wrench do i need to remove the brake pads on a 1986 chevy celebrity

    You'll need some metric size wrenches. Usually a 13mm and a 15mm or 16mm. Some also use an allen head socket. Auto Zone sells a rack of 5 allen sockets to fit most autos using that set up.

    May 01, 2010 | 1986 Chevrolet Celebrity

    1 Answer

    What is the size of the allen wrench needed to fit the oil pan drain plug in a 1995 toyota celica

    The oil pan drain plug should require a 14mm hex head wrench to remove. The transmission pan requires a 10mm allen head socket, or wrench to remove. Are you sure you're trying to remove the correct drain? The oil drain should be on the passenger side and on the rear corner of the pan.

    Dec 12, 2009 | 1995 Toyota Celica

    3 Answers

    1990 honda crx si, 1.6 transmission

    No verify by havin car first on level ground then.Then when on stable ground remove the 17mm filler plug on upper passenger side of transmission.if fliud flows out of filler plug than level is fine.if does not flow out whenplug removed.RECOMMEND STRONGLY using a honda brand manual transmission fluid in this does wonders for shifting or gearing issues.

    Aug 01, 2009 | 1990 Honda CRX

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    78 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    80263 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides