Question about Ford Escape

1 Answer

I have 2002 ford escape and the windshield wipers wont work what could be the problem

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 109 Answers

Fuses, disconnected power, or a bad wiper motor - check the connections on the wiper motor - make sure wires are not worn and frayed so there is a good solid connection - check you fuse block the fuses should be identified in the manual or on the fuse panel door. If neither of those are the issue go to AutoZone and ask for current check on the wiper motor

Posted on Jan 13, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 70 Answers

SOURCE: cruise control ford escape 2002. ford escape

If the cruise lamp comes on and the cruise does not set i would advise inspecting the cruise cable and make certain it is not broken, if ok the the servo has likely failed.

Posted on May 29, 2010

  • 1 Answer

SOURCE: 2002 ford escape liftgate wont lock/unlock

Had same problem on Ford Escape, Could not unlock the rear liftgate or window, if you can open you are in better luck.
If it is locked and closed, you will have to pull the top portion of the plastic trim away from the liftgate, it is held in place by metal retaining clips on top, and four screws on the bottom, if you can open, remove the screws then remove the rest of the panel, if unable, pull the top of the panel just far enough to reach in and unlock the liftgate.
Once you have the gate open and the panel off, you will see the locking actuator connected to the electrical connetion, it is a little bit smaller then a pack of cigarettes with a black lever.

To remove you will need to remove the two outter 10mm nuts holding the "brass" colored assembly, you will probably have to disconnect the two lever connections to get to the back side of the brass assembly, once this is done, you can use a T-20 torx to remove the locking actuator, part number stamped on my part was 4510 5424 made by KIEKERT although a search of this part didnt give me any good results, anyway, that was the cause of my problem, once replace and all put back together everything worked fine.

Posted on May 10, 2009

  • 65 Answers

SOURCE: 98 ford windstar. power windows, windshield wipers,willnot work,.

This sound like some type of relay switch failure in the fuse box, you need check all the fuses and see if they're all intact and make sure none of them are burned out. If all these are not working you have a live wire some where in you wire harness

Posted on Aug 19, 2009

steve_e_uk
  • 1675 Answers

SOURCE: 2000 VW jetta VR6 windshield wipers wont work

first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Posted on Feb 08, 2010

  • 246 Answers

SOURCE: ford f150 windshield wiper bushing diagram

sounds like a loose nut. there are nuts that hold the wiper arms on, they may be under a cover but theyre at the base of the wiper arm. also there's a nut that holds the wiper linkage onto the wiper motor. if you can move the wipers independently, it's the nuts connecting the wiper arms.if you move one arm and the other moves with it, it's the nut holding the linkage to the motor.

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

2 Answers

2002 ford escape 3L 4x4 wipers wont turn off and wont spray washer fluid what could the problem be


if your wipers will not turn off then it most certainly is not a wiper motor problemboth of your problems sound like a switch problem

Jan 10, 2015 | 2002 Ford Escape

1 Answer

Fan lights windshield wipers do not work on 2002 pontiac star fire


what is fan lights windshield wiper ???????
tell me what is the problem if it is wiper don't work or else
tell me what you did to correct the problems

Apr 22, 2014 | 2002 Pontiac Sunfire

1 Answer

2002 escape stalls when turning windshield wipers.Like if wipers motor is not strong enough to make it work.


Wiper motors suffer this problem when the bushes on the shaft at the bottom of the wiper arms are dry an tighten on the shafts. If you remove the wiper arms and the dust cap under them you may be able to free up the shafts by spraying WD 40/ CRC on the shaft and let it run down into the bush as the wipers are working Other than that it is wipers out for the job.

Mar 20, 2013 | Ford Cars & Trucks

1 Answer

Replacing wiper linkage


WINDSHIELD WIPERS


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below: -------


1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Nov 29, 2012 | 2003 Chevrolet Cavalier

1 Answer

Where is fuse for wiper fluid pump on a 2003 cavalier?


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Nov 28, 2012 | 2001 Saturn S-Series

1 Answer

How to remove the windshield cowl on a 2002 tyota yaris


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------


Complete wiper components replacing details ?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------



1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------


These details will help.

Thanks.

Nov 28, 2012 | Toyota Yaris Cars & Trucks

2 Answers

2002 intrigue wipers / washer dont work


It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function.If yes then fuse is ok,but issue is wiper motor.
If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----
For complete troubleshooting i suggest you few helpful links with accurate solutions.
-------------
Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html
------------ How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html


-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------
These details will help.
Thanks.



Nov 27, 2012 | Oldsmobile Intrigue Cars & Trucks

1 Answer

How do I change the Windshield wiper motor on my 2002 Ford Escape?


Pinch the tab between the wiper and the arm to remove the blade

Aug 18, 2010 | 2002 Ford Escape

1 Answer

Drivers side windshield wiper went past the window. Now it doesn't move at all. the wiper also can be moved by hand with the motor off.


The base nut needs to be tightned, with the key on and wipers off, now turn key off and position wiper in the park position (down) then tight the nut,remove the cover at the bottom of the arm to see nut,75c3630.gif

Mar 31, 2010 | 2002 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...