Question about Cars & Trucks

1 Answer

How to remove the interior panel on the rear door nissan tiida hatchback?

Hi. I need to remove the plastic interior panel on the rear door of my Tiida, so I can push out a small dent beside the exterior handle. I'm assuming it's simply clipped on, but I don't want to force it until I'm sure. Cheers, Matt.

Posted by on

  • Matt Cairns Jan 13, 2013

    Great. Thanks so much.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,280 Answers

There should be at least one screw holding the door handle trim piece. And check for other screws, like on the door pull or armrest, may be hidden behind small rectangular or square caps or plugs that are pried off to reveal the screws. The bottom and up the sides of panel should be held by plastic pins that push in to secure. Use a putty knife or screwdriver under the panel at bottom to pry the pins out. Work carefully all around trying not to break any of the plastic retainers (although they can be replaced if broken. When all free of the plastic retainers, pull panel out from bottom and lift up and away from the window channel. Unplug any electrical connections, and panel should be free.

Posted on Jan 12, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MauiRentaCar
  • 288 Answers

SOURCE: 1991 corolla door rod handle plastic clip broken

You can get inside door handle either new or used from sellers on ebay. It should be just a few dollars plus shipping. Just search ebay for "Inside door handle 1991 Toyota Corolla."

Frank
Frank's Friendly Cars Maui Car Rental
www.MauiCarRental.biz

Posted on Aug 30, 2009

  • 1986 Answers

SOURCE: need to remove inner rear passenger side door

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removal of rear door lift hatch interior plastic panel on a 2005 Dodge Grand Caravan to push out dent in metal door from the inside.


The rear door panel is secured to the door using screws and clips. The screws will be in the handle used to close the door and there may be plastic plugs in the handle hiding the screws. Once these screws are removed, the handle will come off. Look for any more screws along the panel. If there are more, they will be visible. Once the screws are removed, pull on the panel to release the clips that secure it to the door. These clips will require some force to release them and will make a snap/pop sound once released. You may have to put a screwdriver/wedge between the panel and door to start the process of releasing the clips

Jan 20, 2016 | 2005 Dodge Grand Caravan

1 Answer

How do i remove inside rear door panel on fiesta 2015


Ford Fiesta Plastic Interior Door Panel Removal Guide ...

www.paulstravelpictures.com/Ford-Fiesta-Interior-Door-Panel-Removal-...
Ford Fiesta Interior Door Panel Removal Guide How to take off the plastic interior door panels in a 6th generation 2009-2015 Ford Fiesta to upgrade the ...

Ford Fiesta inner door panel removal (I removed the top one ...

www.fiestafaction.com/.../44959-Ford-Fiesta-inner-door-panel-removal-...

Jan 19, 2015 - 10 posts - ‎3 authors
This is an excerpt from the manual: Remove the rear door window glass. ... Route theinterior door handle cable and door lock actuator electrical connector through the ...Last edited by WildmaninME; 01-19-2015 at 07:41 PM.

Ford - door panel removal - fiesta - YouTube

? 2:19
https://www.youtube.com/watch?v=1URT13Yusjg
Oct 19, 2013 - Uploaded by one2three
this is the removal of a door panel from a ford fiesta 2001. ...Replacing Broken Inside Door Handle on 2007 Ford Fusion - Duration: 5:32. ... Ford Fiesta 1.25 2004 - Cleaning and adjustingrear brake drums - Duration: 8:47.

How To: 2012+ Ford Focus Rear Door panel removal(SE,ST ...




Jan 13, 2016 | Cars & Trucks

1 Answer

How do I remove the rear sliding door interior panel on 2001 Nissan Quest?


Mostly clips, screws hold the handle on and bezel around it has clips that can carefully be pried off.. A door panel tool should be used to enage and pry panel clips off

Aug 22, 2014 | 2001 Nissan Quest

1 Answer

Remove interior rear door panel


On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

May 13, 2010 | 2007 Jeep Liberty Sport

2 Answers

How do i remove a door panel of my 2005 nissan sentra ?


If it is the rear door panel, you start by lifting, pulling upward, the door closer/arm rest.
Remove the electric window control and disconnect wire from switch.
Remove two hex/phillip head screws which are visible when you remove arm rest.
Remove a plastic screw on rear edge of door located about 6 inches below window glass.
Gently pry around edges of door panel to force plastic fasteners (approximately 6) out.

Oct 25, 2009 | 2005 Nissan Sentra

1 Answer

How to remove drivers door panel on a 2007 Nissan Tiida hatchback


The door handle has a c clip behinde it that you can not see.Goto a auto parts store and thay will have a cheep tool to help you.(you need a special tool for this. The WINDOW CRANK handle has a 'c-clip' behind it. The door opening handle trim is held in by either a screw behind a plastic flap that will pop out(behind the lever)or it is held in at four points by plastic tabs (two on top and two on the bottom)that can be undone carefully with a screwdriver or the like. When this plastic trim is removed the door panel should come off.
Be aware that there are plastic clips (back side of the panel) on the perimeter of the panel that hold it in as well.
the tweeter panel just pops out look on the bottom of the door for screws and around the door handle and you will have to pop your window and door lock controls out and the reflector on the door pops out and there is two screws there then al you have is the clips behind the door they make tools for it but a flat tip screwdriver will be fine just get the tip close to the clip and pull it out .
1. Remove window crank (it has a kind of 'bent wire' c-clamp, which holds it onto the window crank shaft). 

2. Pry upwards the top plastic cover to the arm rest (this is a plastic coated foam rubber piece, on which you rest your arm). 

3. Remover the two now visible screws which fasten the arm rest onto the door. 

4. Remove the one screw fastening the inside door handle. 

5. With a blunt tool, gently hit the inside door handle in a forward direction (towards the door hinge). This will release the door handle from the door. 

6. Pry between the door panel and the door, to unsnap the snaps holding the door panel in place. 

7. Finally, lift door panel out and up to remove it from door. 

Feb 09, 2009 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE


There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Nov 09, 2008 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...