Question about 1991 Oldsmobile Cutlass Ciera

1 Answer

Brake pedal all the way to the floor - 1991 Oldsmobile Cutlass Ciera

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Put brake fluid in the resevoir

Posted on Jan 12, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My brake pedal goes all the way to the floor


Brake pedal goes to the floor? When does it happen. That is the most important piece of information. Most brake systems are power assisted via vacuum from the engine. Your brake booster is what makes the "power assist" work. There are some specific times when you will feel your brake pedal "fade" to the floor and it is normal due to the cycle of the brake components operation.If your brake pedal goes to the floor every time you step on it, stop driving and get to a repair facility! If the pedal is working when driving and the vehicle seems to be working as it always has, then chances are there is no concern. To be on the safe side, have it checked the next time you are in for any other type of service.There is a sensor inside most brake reservoirs that activates the indicator light in your instrument cluster when the level is lower than it should be. As your brake pads wear down, the system requires more fluid so the level at the reservoir drops setting the light. Same thing if there is a leak. The fluid level drops and the light goes on. This brake fluid leak would most likely be combined with a spongy pedal or a pedal fade every time you step on the brakes. A leak would also almost always have a wet area around the leak. Sometimes the leak can be internal to a part of the car you cannot see, so don't count on it.One easy way to check most brake boosters and the brake system for leaks is to turn the vehicle off and pump the brake pedal. Every time you depress the pedal you should feel the pedal "height" come up and the pedal get harder. After a few firm pumps of the pedal, hold it down. Leave pressure on the pedal for 20 seconds or so. Does the pedal move slowly (or quickly) to the floor? If so then there is a leak somewhere in the system. Keeping pressure on the brake pedal, start the vehicle. Does the pedal no drop? It should. That is the power assisted vacuum kicking in as the engine starts to run.The bottom line is that we are talking about your brakes. Your life, your passengers lives and the lives of others on the road around you depends on that system working properly. If you have any doubts, or feel uncomfortable, take it in to have it looked at. Know specifically what it is doing so that you can have your repair facility look at what you are feeling and tell you if

Oct 29, 2011 | 1987 Nissan Pickup

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

How to bleed the brakes after you replace rear brake lines


hi, if you look at the back of the brake drum you will see a little bleed nipple just sticking out think its an 8ml or 10ml spanner fit, what you then need to do is find a piece of plastic pipe that will fit over the top of this to catch any fluid then make sure the brake fluid is topped up, you then need someone in the car to operate the brake pedal and some one at the back where the bleed nipple is once you have this you need to do the following

1 undo bleed nipple a couple of turns
2 get person in the car to push brake pedal to the floor and hold it on the floor.
3 when pedal is at floor tighten the bleed nipple up and get the person to let the brake pedal come up.
4 when pedal is up all the way undo bleed nipple and get person in car to push pedal to floor.
5 when pedal at floor tighten bleed nipple up
6 let pedal up
7bleed nipple undo a bit
7 pedal down to floor
8bleed nipple do up
9 pedal up
10undo bleed nipple

now keep doing that until all you have got coming out is fluid and no air when you have this do bleed nipple up and check the brakes to make sure they are not spongy.

whilst doing this you need to make sure the brake fluid level dont drop to low as you will have to bleed the front as well so keep checking the level and make sure its well topped up throughout the whole process

if you have any problems give me a shour back ok

Aug 14, 2010 | 1998 Chrysler Cirrus

1 Answer

Brake pedal goes to floor on first depression; then pumps up fine


Try this,apply the emergency before stepping on the brake.
If this helps the pedal,the rear brakes are out of adjustment.

Jul 01, 2010 | 2000 Saturn L-Series

1 Answer

Brake pedal goes to the floor


check vacumn and\or connections to the vacumn boost cannister.

Apr 21, 2010 | 1985 Ford F150

2 Answers

With motor running, brake pedal goes to floor and swoosh of air is heard


Could be brake booster leaking. When engine is off the brake pedal should be firm and not go to the floor. If the pedal goes to the floor engine off, there may be a master cylinder problem also.

Oct 28, 2009 | 2005 GMC Envoy Xl

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Brake pedal to floor


Change the brake caliper. This should do it.

Rate this

Apr 05, 2009 | 1995 Toyota Camry

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
1991 Oldsmobile Cutlass Ciera Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...