Question about 1983 GMC G1500

Open Question

HOW MANY BOLTS ON AN EXHAUST HEAT SHIELD 1999 VOLTSWAGON BEETLE 2.0l

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the starter on a 1999 Oldsmobile Cutlass


Lift car on jack stands, disconnect the car battery and while under car you will find two bolts that hold it heat shield on front and back of starter. After removing the heat shield, this will give you access to the bolt against the engine on top. Two other bolts easy to get to. Disconnect wires to starter and then remove bolts. Install in opposite procedure

Nov 12, 2016 | 1999 Oldsmobile Cutlass

1 Answer

My husband and I are trying to get to our thermostat to change in my 2002 rendezvous, but there is a metal pipe in the way that we can't figure out how to remove. just behind the pipe, is a metal plate...


Hello vocalviixen,

The pipe that you referred to is the exhaust crossover pipe. Below I've included removal and installation instructions.

Also, the procedure for bleeding the coolant system is critical; if you need those instructions please post the question.

REMOVAL PROCEDURE
1. Disconnect the battery ground (negative) cable.
2. Remove the throttle body air inlet duct.
3. Drain the coolant from the cooling system.
4. Remove the inlet radiator hose from the engine.
5. Remove the thermostat bypass pipe.
6. Remove the exhaust crossover heat shield bolts.
7. Remove the exhaust crossover heat shield.
8. Remove the exhaust crossover pipe studs/nuts.
9. Remove the exhaust crossover pipe.
INSTALLATION PROCEDURE
1. Install the exhaust crossover pipe.
2. Install the exhaust crossover pipe studs/nuts.
3. Tighten the exhaust crossover pipe studs/nuts to 18 lb ft.
4. Install the exhaust crossover heat shield.
5. Install the exhaust crossover heat shield bolts.
6. Tighten the exhaust crossover heat shield bolts to 89 lb in.
7. Install the thermostat bypass pipe.
8. Install the inlet radiator hose to the engine.
9. Fill the cooling system with engine coolant.
10. Install the throttle body air inlet duct.
11. Connect the battery ground (negative) cable.


Regards,
netvan

Mar 14, 2011 | 2002 Buick Rendezvous

1 Answer

JUST HAD MY FUEL PUMP FIXED AND NOW I GET RUMPING NOISE FROM THE AXLE


there is an exhaust pipe heat shield that could b the cause, tel them to make sure that the heat shield is secured properly, bolts and fasteners torqued.

Jan 15, 2011 | 1999 Chevrolet Blazer

1 Answer

How do u take off the starter


3.2L Engines

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following: Negative battery cableHeated Oxygen (HO2S) sensor connectorsExhaust front pipeHeat shieldStarter wiring connectorsStarter motor
Negative battery cable
Heated Oxygen (HO2S) sensor connectors
Exhaust front pipe
Heat shield
Starter wiring connectors
Starter motor

To install:

1. Install or connect the following: Starter motor. Tighten the bolts to 30 ft. lbs. (40 Nm).Starter wiring connectorsHeat shieldExhaust front pipeHeated Oxygen (HO2S) sensor connectorsNegative battery cable
Starter motor. Tighten the bolts to 30 ft. lbs. (40 Nm).
Starter wiring connectors
Heat shield
Exhaust front pipe
Heated Oxygen (HO2S) sensor connectors
Negative battery cable

Hope helps (remember to rate this).

Nov 08, 2010 | 1999 Isuzu Rodeo

1 Answer

How do I replace a water pump on a 1999 malibou with a quad 4?


Water Pump REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old. 2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  9. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  10. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt. NOTE: DO NOT rotate the flex coupling more than 4┬░or damage may occur.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  12. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  13. Carefully lower the vehicle.
  14. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  15. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  16. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces. Fig. 1: Water pump and cover mounting - 2.4L engine 87953070.gif
    To install:
  17. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  18. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  19. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  20. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  21. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  22. Raise and safely support the vehicle.
  23. Index the exhaust manifold bolts into the exhaust pipe flange.
  24. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  25. Connect the radiator outlet pipe to the transaxle and oil pan.
  26. Install the timing chain tensioner and front cover.
  27. Install the lower heat shield.
  28. Carefully lower the vehicle.
  29. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  30. Tighten the manifold-to-exhaust pipe nuts to specification.
  31. Install the upper heat shield.
  32. Attach the oxygen sensor connector.
  33. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  34. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  35. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.

Oct 26, 2010 | 1999 Chevrolet Malibu

1 Answer

Location of thermostat on 2002 olds alero 2.2


Thermostat Removal & Installation 2.2L Engine To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt.
      1. Tighten bolt to 89 in lbs (10 Nm).
    • Exhaust manifold if equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L Engine To Remove:
Thermostat assembly 2.4L 87953024.gif

  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield.
  3. Remove the coolant inlet housing mounting bolts through the exhaust manifold.
  4. Raise and safely support the vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove wheel and tire assembly.
  7. Remove the engine splash shield.
  8. Remove the mounting bolts from the transaxle-to-engine block support. Remove the support.
  9. Remove the coolant housing pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the coolant housing pipe.
  3. Install and secure the transaxle support-to-engine block mounting bolts.
  4. Install the engine splash shield.
  5. Install the wheel and tire assembly.
  6. Install the coolant inlet housing stud to the oil pan.
    • Tighten to 19 ft lb (26 Nm).
  7. Lower the vehicle.
  8. Install the coolant inlet housing bolts through the exhaust manifold.
    • Tighten the coolant inlet housing bolts to 10 ft lb (14 Nm).
  9. Install the exhaust manifold heat shield.
  10. Fill the cooling system.
  11. Inspect the system for leaks.
3.4L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat.
To Install:
  1. Install the thermostat and housing outlet.
  2. Install the thermostat housing bolts.
    • Tighten the thermostat housing bolts to 18 ft lb (25 Nm).
  3. Install exhaust crossover pipe.
  4. Connect the surge tank line fitting to the coolant outlet.
    • Tighten the fittings to 15 ft lb (21 Nm).
  5. Install the air cleaner.
  6. Fill the cooling system.
  7. Inspect the system for leaks
prev.gif next.gif

Oct 14, 2010 | Oldsmobile Alero Cars & Trucks

2 Answers

Where is the thermostat on a 2.2l ohc engine?


Removal & Installation 2.2L VIN 4 To Remove:
  1. Drain the cooling system.
  2. Remove the lower radiator hose from thermostat housing.
  3. Remove the thermostat housing bolts and outlet.
  4. Remove the thermostat.
  5. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the thermostat housing and bolts.
  3. Install the coolant housing bolts. Tighten bolts to 14 Nm (10 ft. lbs.).
  4. Install the lower radiator hose to thermostat housing.
  5. Fill the cooling system.
  6. Inspect for leaks.
2.2L VIN F To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt. Tighten bolt to 10 Nm (18 in. lbs.).
    • Exhaust manifold. If equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L VIN T To Remove:
  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield bolts and shield. cavman.gif

    cavtstat.gif

  3. Remove the coolant inlet housing bolts.
  4. Lift vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove the wheel.
  7. Remove the right engine splash shield.
  8. Remove the transaxle-to-engine block brace bolts and brace.
  9. Remove the radiator outlet pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Clean the mating surfaces.
  2. Install the thermostat.
  3. Install the radiator outlet pipe.
  4. Install the transaxle-to-engine block brace and install bolts.
  5. Install the right engine splash shield.
  6. Install the wheel.
  7. Lower the vehicle.
  8. Install the exhaust manifold heat shield and bolt.
  9. Tighten the exhaust manifold heat shield bolts to 14 Nm (10 ft. lbs.).
  10. Fill the cooling system.
  11. Inspect the system for leaks.
prev.gif next.gif

Sep 09, 2010 | 2003 Pontiac Sunfire

1 Answer

Where are the exhaust system bolts located?


Removal & Installation 2.2L Engine To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable.
    • Heat shield.
    • Oxygen sensor.
  2. Raise and safely support the vehicle.
  3. Remove exhaust pipe from the exhaust manifold.
  4. Lower the vehicle.
  5. Remove the exhaust manifold mounting nuts from the cylinder head. chevy_cav_02-04_exmanifold.gif

  6. Remove the exhaust manifold.
  7. Clean the mating surfaces.
  8. Check for cracks, broken flanges and gasket surface damage.
  9. Use a straight edge and a feeler gauge. If the flanges or the mating surfaces do not align, the manifold is warped and should be replaced.
To Install:
NOTE: The manufacturer recommends using new exhaust system nuts.
  1. Install the manifold gasket.
  2. Position the exhaust manifold to the cylinder head. Exhaust manifold 2.2L 87953055.gif

  3. Install the new exhaust manifold nuts. Tighten the nuts starting from the center and working toward the ends to 110 in lbs (12.5 Nm).
  4. Raise and safely support the vehicle.
  5. Install the exhaust pipe to the manifold using a new flex coupler gasket.
  6. Install new exhaust flange mounting nuts.
    • Tighten to 33 ft lbs (45 Nm).
  7. Lower the vehicle.
  8. Install the oxygen sensor.
  9. Install the heat shield.
  10. Connect the negative battery cable.
2.4L Engine To Remove:
  1. Disconnect the negative battery cable
  2. Disconnect the Oxygen (O2) sensor electrical connector.
  3. Remove the (O2) sensor.
  4. Raise and safely support the vehicle. Exhaust brace 2.4L 87953053.gif

  5. Remove the exhaust manifold brace-to-manifold bolt and the oil pan nuts, if necessary. Exhaust heat shield 2.4L 87953051.gif

  6. Remove the upper heat shield. NOTE: Do NOT bend the exhaust flex decoupler more than necessary to remove it. Excessive movement will damage the flex decoupler
    Exhaust flex decoupler 87953056.gif

  7. Remove the manifold-to-exhaust flex decoupler fasteners.
  8. Remove the exhaust pipe.
  9. Carefully lower the vehicle.
  10. Remove the exhaust manifold-to-cylinder head mounting nuts/bolts. Remove the exhaust manifold.
  11. Discard the gaskets and/or seals. Clean the mating surfaces.
To Install:
Exhaust manifold 2.4L 87953055.gif

  1. Install new exhaust manifold gaskets. Position the exhaust manifold on the cylinder head. Tighten the mounting bolts in sequence to 110 in lbs (12.5 Nm).
  2. Raise and safely support the vehicle.
  3. Install the exhaust manifold heat shield. Tighten the mounting bolts to 10 ft. lbs (14 Nm).
  4. Install the exhaust manifold brace-to-manifold bolt and the oil pan nuts. Tighten the mounting bolts to 41 ft lbs (56 Nm) and the nuts to 18 ft lbs (24 Nm).
  5. Position the exhaust pipe to the manifold. Install the manifold-to-flex decoupler mounting bolts. Tighten to 26 ft lbs (35 Nm).
  6. Lower the vehicle.
  7. Coat the threads with a suitable anti-seize compound and install the O2 sensor.
  8. Connect the O2 sensor electrical connector.
  9. Connect the battery ground cable and check for leaks.
prev.gif next.gif

Sep 02, 2010 | 2000 Oldsmobile Alero

1 Answer

Torque for 2004 hummer h2 exhaust manifold bolts


Exhaust manifold bolts-first pass 11 Lb/Ft. Exhaust manifold bolts-final pass 18 Lb/Ft. Exhaust manifold heat shield bolts 7 Lb/Ft. Note: To torque bolts & nuts, start in center using crisscross pattern working outward

Apr 26, 2010 | 2004 Hummer H2

1 Answer

How do i change my thermostat on my 2001 pontiac aztek. also how do i remove the crossover exhaust pipe to get to the @#$%^ing thing?


Exhaust Crossover Pipe Replacement
Removal Procedure
  1. Disconnect the battery ground (negative) cable.
  2. Remove the throttle body air inlet duct.
  3. Drain the coolant from the cooling system.
  4. Remove the inlet radiator hose from the engine.
  5. Remove the thermostat bypass pipe.
  6. Remove the exhaust crossover heat shield bolts.
  7. Remove the exhaust crossover heat shield.
89160026

  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.
  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
Removal Procedure

89153578

Dec 11, 2009 | 2003 Pontiac Aztek

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...