Question about 2007 Hyundai Accent GS Hatchback

1 Answer

Feels like misfiring but diagnostics say no misfire.

Diagnostics pull up "Purge or vent solendoid failure" "Plugged EVAP canister condition" and/or "Failed EVAP pressure sensor." Car feels like it's sputtering or attempting to shut off during idling and has a misfire feel while accelerating through 30 to 45 MPH.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

How many miles on vehicle?

Posted on Nov 28, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 148 Answers

SOURCE: car hesitates to accelerate and feels as though it will stall

take the car back to where the oil was changed at and make sure they did not over fill the oil then ask them if they looked at your air filter and disconnect a vaccum line or the MAF sensoer

Posted on Jul 17, 2009

  • 1 Answer

SOURCE: almost no acceleration engine will not top 2K RPM under load.

Have you checked the air inlet sensor on the air filter. If this fails the engine goes into safety mode which it seems has happened. I don't know the specifics of the Santa fe but this is a feature of most modern electronic engine systems.

Posted on Nov 12, 2012

Testimonial: "Will check those - thanks for the tip. Read my update..."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Jeep Grand Cherokee limited,V8 Quadra-trac which dies on the road; dash gauges drop; "no key" lite displays on dash. Restarts after cools. Two codes P 0443 and 0308 are showing? help


code p 0443 refers to evaporative emission (EVAP) canister purge valve ---circuit malfunction====causes ---wiring--- EVAP canister purge valve ---ECM
code p0308 refers to cylinder 8 ---misfire detected ====causes ---engine mechanical fault ---wiring----ignition/ fuel system--- injector---ECT/MAF sensor---ECM
I am thinking here that it restarts , not after cooling , but after the vacuum in the fuel tank has lessened and allowed fuel to be pumped to the injectors and the fuel pressure is re-established
if that is the case then a weak injector or partially blocked injector will misfire under those conditions
I would fix the purge valve so that the tank vents properly and the rest may go away

Feb 18, 2017 | 1999 Jeep Grand Cherokee Limited

1 Answer

How can I replace a canister vent solenoid for a 2006 Chevy Tahoe code 449/300


Google the location & a picture & replace yourself

Has to be near the fuel tank

PO449 is the Evap Vent Solenoid

PO 300 is random cylinder misfires maybe from the
extra air, when the evap purge runs

Aug 13, 2014 | Cars & Trucks

1 Answer

P1300


Error Code: P0301
Description:
Cylinder 1 - Misfire Detected
Possible Cause:
Wiring.
Ignition system.
Fuel injectors.
Fuel pressure.
Running out of fuel.
EVAP canister purge valve.
Evaporative emission system.
Low compression.
Base engine problems.
Engine control module (ECM).

Error Code: P0302
Description:
Cylinder 2 - Misfire Detected
Possible Cause:
Wiring.
Ignition system.
Fuel injectors.
Fuel pressure.
Running out of fuel.
EVAP canister purge valve.
Evaporative emission system.
Low compression.
Base engine problems.
Engine control module (ECM).

Error Code: P1300
Description: Random Misfire

Possible Cause:
As above.

Jan 22, 2014 | 1996 Honda Civic

1 Answer

Whats code p1441


Hi there:DTC P1441 - EVAP System Flow During Non-Purge




CIRCUIT DESCRIPTION
The evaporative system includes the following components:


The fuel tank.
The EVAP canister vent valve.
The fuel tank pressure sensor.
The fuel pipes and hoses.
The fuel cap.
The EVAP vapor lines.
The EVAP purge lines.
The evaporative emission canister.
The EVAP purge valve.


The Powertrain Control Module (PCM) supplies a ground to energize the valve (purge ON). The EVAP purge valve control is Pulse Width Modulated (PWM) or turned ON and OFF several times a second. The duty cycle (pulse width) is determined by engine operating conditions including load, throttle position, coolant temperature and ambient temperature. The duty cycle is calculated by the PCM and the output is commanded when the appropriate conditions have been met. The system checks for conditions that cause the EVAP system to purge continuously by commanding the EVAP canister vent valve ON and the EVAP purge valve OFF (EVAP canister vent valve CLOSED, EVAP purge PWM 0%). If vacuum level in the fuel tank increases during the test, a continuous purge flow condition is indicated. This can be caused by any of the following conditions:


EVAP purge valve leaking.
EVAP purge and engine vacuum lines switched at the EVAP purge valve.
EVAP purge valve control circuit grounded. If any of these conditions are present, DTC P1441 will set.


CONDITIONS FOR SETTING THE DTC


No Throttle Position (TP) sensor, ODM, IAT sensor, or MAP sensor DTCs set.
The DTC P0442 diagnostic test has passed.
A continuous open purge flow condition is detected during the diagnostic test (fuel tank pressure decreases to less than -11 in. H20).


ACTION TAKEN WHEN THE DTC SETS


The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.


NOTE: Although these diagnostics are considered type A, they act like type B diagnostics under certain conditions. Whenever the EVAP diagnostics report that the system has passed, or if the battery has been disconnected, the diagnostic must fail during two consecutive cold start trips before setting a DTC. The initial failure is not reported to the diagnostic executive or displayed on a scan tool. A passing system always reports to the diagnostic executive immediately.


CONDITIONS FOR CLEARING THE MIL/DTC


The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.

The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed.


DIAGNOSTIC AIDS
Check for the following conditions:


Poor connection at the PCM.
Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.


Damaged harness.
Inspect the wiring harness for damage.


If the harness appears to be OK, connect the J 41413 EVAP pressure/purge diagnostic station to the EVAP service port, pressurize the EVAP system to 10 in. H2O and observe the Fuel Tank Pressure display on the scan tool while moving connectors and wiring harnesses related to the EVAP purge valve. A sudden change in the display will indicate the location of the malfunction.
Incorrect vacuum line routing.
Verify that the source vacuum line routing to the EVAP purge valve is correct and that the EVAP purge and source vacuum lines to the EVAP purge solenoid are not switched.


Malfunctioning or damaged canister.
A malfunctioning canister may intermittently allow charcoal into the EVAP purge solenoid, vacuum switch, and associated lines causing a DTC to be set. Use the following procedure to check for a carbon release condition:


Turn OFF the ignition switch.
Remove the EVAP purge valve.
Lightly tap the EVAP purge valve and (if applicable) the vacuum switch on a clean work area looking for carbon particles exiting either of the vacuum ports.
If no carbon release is evident, reinstall the components and continue with the DTC P1441 table. If carbon is being released from either component, continue with this service procedure.
Remove the charcoal canister from the vehicle.
Ensure that the main cylinder valve is turned off on the J 41413 EVAP purge/pressure diagnostic station.
Disconnect the black hose that connects the nitrogen cylinder to the EVAP purge/pressure diagnostic station at the pressure regulator by unscrewing the knurled nut on the regulator. No tools are required to remove the black hose from the regulator.
Using a section of vacuum line, connect one end over the open threaded fitting of the EVAP purge/pressure diagnostic station pressure regulator.
Connect the remaining end to the EVAP purge valve end of the EVAP purge line at the vehicle and turn on the main nitrogen cylinder valve. Continue to blow any debris from the purge line for 15 seconds.
Return the EVAP Pressure/Purge Diagnostic Station to its original condition by re-installing the black hose that was disconnected in step 7.
Replace the following components:
The EVAP purge valve.
The EVAP canister.
Proceed with the the DTC P1441 diagnostic table.
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to set occurs. This may assist in diagnosing the condition.


TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table.


If an EVAP purge valve electrical malfunction is present, the purge system will not operate correctly. Repairing the electrical malfunction will very likely correct the condition that set DTC P1441.
Checks the Fuel Tank Pressure sensor at ambient pressure
Checks for a stuck open EVAP purge valve.
Verifies that the fuel tank pressure sensor accurately reacts to EVAP system pressure changes.
If the EVAP purge and engine vacuum lines are switched at the EVAP purge solenoid, the solenoid valve will leak vacuum.
The PCM will command the EVAP purge and EVAP canister vent valves closed with the scan tool Seal System EVAP output control function activated. Fuel tank pressure should not decrease under this condition.


Hope this helps.

Jun 25, 2012 | 1999 Buick Century

3 Answers

2000 Ford Expedition My Expedition (4.6L V-9 2WD) has had an intermittent problem of cutting out. The Check Engine light was not coming on - so I figured it is not a misfire. It drove just like it had...


Continuous Memory Diagnostic Trouble Code (DTC) P0446 or P1450 indicates that Self-Test has detected the Evaporative Emission Control System has excessive fuel tank vacuum. Also, a DTC P0446 indicates a vent control malfunction.

Possible causes:

EVAP canister purge outlet tube (EVAP canister purge valve to EVAP canister) blockages or kinks.

EVAP canister tube (fuel tank to EVAP canister) blockages or kinks.

Fuel vapor elbow on EVAP canister contaminated.

Restricted EVAP canister.

Canister vent (CV) solenoid stuck closed (partially or fully).

Plugged or contaminated CV solenoid filter.

EVAP canister purge valve stuck open.

Fuel filler cap stuck closed (no vacuum relief).

VREF circuit open in fuel tank pressure (FTP) sensor.

Damaged FTP sensor. (fuel tank pressure)

Check for kinks or bends in the fuel vapor hoses/tubes (EVAP canister purge outlet tube and EVAP canister tube).

Visually inspect EVAP canister inlet port, CV solenoid filter and canister vent hose assembly for contamination or debris.

Check CV solenoid filter for blockage or contamination.

The common things I've seen are are mud in the canister and the canister vent solenoid being shot or the wiring to the canister vent solenoid being torn off. The resistance of the solenoid should be 48-65 ohms..
Pick up a Chiltons book and will give you a diagram of where exactly you find the canister. They are like $15 at any auto store. Good luck

May 22, 2011 | 2000 Ford Expedition

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

3 Answers

Emission control malfuction p0440


Easier said then done without professional tools

However, I'll start you will some theory, then the shop manual procedures followed by some "common" problems

Theory:
Evaporative leak detection strategy is based on applying vacuum to EVAP system and monitoring vacuum decay. Powertrain Control Module (PCM) monitors vacuum level by means of fuel tank vacuum sensor input. At a predetermined time, EVAP purge solenoid and EVAP vent solenoid are turned on. This allows engine vacuum to draw a small vacuum on entire EVAP system. Whenever a sufficient vacuum level cannot be achieved, a large leak or faulty EVAP purge solenoid is indicated.

Conditions for setting this DTC are as follows:
No TP sensor, ODM, IAT sensor, or MAP sensor DTCs present.
Start-up ECT 40-86°F (4-30°C).
Start-up ECT not greater than 14°F (8°C) greater than start-up IAT.
Start-up IAT not greater than 4°F (2°C) of start-up ECT.
Fuel tank level is 15-85 percent.
BARO is greater than 75 kPa.
Vehicle has been driven at least 11 miles.
EVAP system is unable to achieve or maintain vacuum during diagnostic test.

Diagnostic Procedures
1.) Perform On-Board Diagnostic (OBD) system check.
After performing OBD system check, go to next step.

2.) Check if DTC P1665 or P1676 is also set. If any of DTCs is present, diagnose affected DTCs. If DTCs are not present, go to next step.

3.) Turn ignition off. Remove fuel filler cap. Turn ignition on. Using scan tool, observe fuel tank pressure. If fuel tank pressure is zero in. H2O, go to next step. If fuel tank pressure in not zero in. H2O, diagnose evaporative system.

4.) Replace fuel filler cap. Using scan tool, capture FAILURE RECORD data for DTC P0440 and clear DTC. Command EVAP vent solenoid on. Connect EVAP Pressure/Purge Diagnostic Station (J-41413) to EVAP service port. Pressurize EVAP system using diagnostic station. Monitor pressure on EVAP pressure gauge on diagnostic station. If pressure is 5 in. H2O, go to next step. If pressure is not 5 in. H2O, go to step 6.

5.) Maintain EVAP pressure at 5 in. H2O. Observe fuel tank pressure on scan tool. If fuel tank pressure reading on scan tool is 5 in. H2O, go to step 8. If reading is not 5 in. H2O, go to next step.

6.) Disconnect fuel tank vapor line and EVAP purge line from EVAP canister. Block canister fitting for fuel tank pressure line. Connect a hand-held vacuum pump to canister fitting for EVAP purge line. Ensure that EVAP vent solenoid is still commanded on. Apply vacuum to EVAP canister. If vacuum can be maintained at 5 in. Hg, go to step 11. If vacuum cannot be maintained at 5 in. Hg, go to step 10.

7.) Check for restriction in fuel tank vapor line or EVAP purge line. Repair as necessary. After repairs, go to step 16. If restriction is not found, diagnose EVAP system.

8.) Disconnect vacuum source line at EVAP purge solenoid and plug vacuum source fitting on solenoid. Using scan tool's output tests function, select and activate SYSTEM PERF. Pressurize EVAP system to 5 in H2O. Observe EVAP pressure gauge on diagnostic station while removing plug from EVAP purge solenoid vacuum source fitting. If EVAP pressure decreases to zero in. H2O within 15 seconds while system performance is activated, go to next step. If EVAP pressure does not decrease to zero in. H2O within 15 seconds, go to step 13.

9.) Install vacuum gauge on EVAP diagnostic station to vacuum source line. Start and operate engine to greater than 2000 RPM. Observe source vacuum level. If vacuum level is greater than -15 in. Hg, If vacuum level is not greater than -15 in. Hg, go to step 14.

10.) Check for disconnected or damaged vent hose. Check for damaged EVAP canister. Repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

11.) Check for faulty or missing fuel filler cap. Check for disconnected or leaking fuel tank vapor line. Check for disconnected or damaged EVAP purge line. If problem is found, repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

12.) Using scan tool, command EVAP vent solenoid on. Continuously attempt to pressurize the EVAP system by leaving the EVAP diagnostic station control knob in the pressurized position. Using the Ultrasonic Leak Detector (J-41416), locate and repair leak in EVAP system. After repairs, go to step 16.

13.) Replace EVAP purge solenoid. After replacing solenoid, go to step 16.

14.) Check for carbon release into the EVAP system. Repair as necessary. After repairs, go to step 16.

15.) Replace EVAP vent solenoid. After replacing solenoid, go to next step.

15.) Turn ignition on. Using scan tool, command EVAP vent solenoid on. Using EVAP diagnostic station, pressurize EVAP system to 15 in. H2O. Move rotary switch in diagnostic station to HOLD and observe EVAP pressure gauge. If EVAP pressure decreases to less than 10 in. Hg within 2 minutes, repeat step 3. If EVAP pressure does not decrease, system is okay.

Diagnostic Aids
Check for the following:
Cracked or punctured EVAP canister.
Damaged or disconnected source vacuum line, EVAP purge line, vent hose, for fuel tank vapor line.
Poor connection at PCM.
Inspect harness connectors for backed-out terminals, improper mating, broken lock, damaged terminals, or poor wire connection.
Check for intermittent in circuit.
Check for kinked, pinched or plugged vacuum lines to EVAP purge or fuel tank vapor line. Also check for restrictions.
Faulty or damaged evaporative canister.

Apr 28, 2010 | 1999 Buick Century

1 Answer

99 5.4 Expedition issues


P0401 - EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
  • Vacuum supply
  • EGR valve stuck closed
  • EGR valve leaks vacuum
  • EGR flow path restricted
  • EGRVR circuit shorted to PWR
  • VREF open to DPF EGR sensor
  • DPF EGR sensor downstream hose off or plugged
  • EGRVR circuit open to PCM
  • VPWR open to EGRVR solenoid
  • DPF EGR sensor hoses both off
  • DPF EGR sensor hoses reversed
  • Damaged EGR orifice tube
  • Damaged EGRVR solenoid
  • Damaged PCM

P1299 - Cylinder Head Over Temperature Protection Active Indicates an engine overheat condition was detected by the cylinder head temperature (CHT) sensor. An FMEM Strategy called Fail-safe Cooling was activated to cool the engine.
  • Engine cooling system concerns
  • Low engine coolant level
  • Base engine concerns

P0300 - Random Misfire The random misfire DTC indicates multiple cylinders are misfiring or the PCM cannot identify which cylinder is misfiring.
  • Camshaft position sensor (CMP)
  • Low fuel: less than 1/8 tank
  • Stuck open EGR valve

P0443 - EVAP Control System Canister Purge Valve Circuit Malfunction The PCM monitors the EVAP canister purge valve circuit for an electrical failure. The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified purge duty cycle by PCM command.
  • VPWR circuit open
  • EVAP canister purge valve circuit shorted to GND
  • Damaged EVAP canister purge valve
  • EVAP canister purge valve circuit open
  • EVAP canister purge valve circuit shorted to VPWR
  • Damaged PCM

P1451 - EVAP Control System Canister Vent Solenoid Circuit Malfunction Monitors the canister vent (CV) solenoid circuit for an electrical failure. The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
  • VPWR circuit open
  • CV solenoid circuit shorted to PWR GND or CHASSIS GND
  • Damaged CV solenoid
  • CV solenoid circuit open
  • CV solenoid circuit shorted to VPWR
  • Damaged PCM

P1309 - Misfire Monitor Disabled When the misfire monitor is disabled, usually due to the input signal generated by the camshaft position (CMP) sensor, by sensing the passage of teeth from the CMP wheel.
  • Camshaft position sensor
  • Powertrain control module
  • ECT, MAF, and CKP sensors

with the codes you have here I would look in the direction of the egr valve first because that will cause the bucking and stalling, and the misfires, but so will the canister vent solonoid. the misfire codes and the cylinder overtemp code could be from overheating or because if the misfires.

Jul 27, 2009 | 1999 Ford Expedition

2 Answers

Error codes P0442 and P0455 in Dodge Dakota 2001


Hello shoretex...Yes sir you can repair this yourself...
p0442 is medium leak detected ...p0456 is small leak....and p0440 is a general evap system failure.. evap codes are a common thing. gas caps are an inexpensive place to start. There are two types of evap hoses on the Dodge... hard plastic and soft rubber.... before you replace parts check the soft rubber first at the evap cans and pump located about a foot in front of the gas tank fill pipe on trucks located next to the transfer case or right behind the trans on the driver side. hard plastic lines will brake or rub through...check spots where lines come in contact with anything. this is a common thing with older trucks...hair line cracks will kick a p0442 code, and a p0445 code...When you find a leak, repair it, and rescan...sometimes there are several leaks, continue with inspection and repairs until you get it all fixed up.... Remember..start at simple and work from there...
i will post the evap. system in more detail to help you troubleshoot the problem.
EVAP System: The Evaporative Emission (EVAP) Control system used on all vehicles is the charcoal canister storage method. This method transfers fuel vapor from the fuel tank to an activated carbon (charcoal) storage device (canister) to hold the vapors when the vehicle is not operating. When the engine is operating, the fuel vapor is purged from the carbon element by intake air flow and consumed in the normal combustion process. The evaporative system includes the following components: *Fuel tank *Evaporative emission canister vent solenoid *Fuel tank pressure sensor *Fuel pipes and hoses *Vapor lines *Fuel cap *Evaporative emission canister *Purge lines *Purge valve solenoid EVAP System Operation: The EVAP purge solenoid valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a ground to energize the EVAP purge solenoid valve (purge on). The EVAP purge solenoid control is Pulse Width Modulated (PWM) or turned on and off several times a second. The EVAP canister purge PWM duty cycle varies according to the operating conditions determined by the mass air flow, the fuel trim, the engine coolant temperature, and the intake air temperature. For certain EVAP tests, the diagnostic will be disabled if the TP angle increases to above 75% . The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring for vacuum decay. The fuel level sensor input to the PCM is used to determine if the fuel level in the tank is correct to run the EVAP diagnostic tests. To ensure sufficient volume in the tank to begin the various diagnostic tests, the fuel level must be between 15% and 85% . The PCM monitors the fuel tank pressure/vacuum level via the fuel tank pressure sensor input. Results of Incorrect Operation: Poor idle, stalling and poor driveability can be caused by the following: *Malfunctioning purge solenoid. *Damaged canister. *Hoses/lines split, cracked and/or not connected properly. Evidence of fuel loss or fuel vapor odor can be caused by the following: *Liquid fuel leaking from the fuel lines *Cracked or damaged canister *Inoperative canister control valve Vacuum hoses that are: *Disconnected *Mis-routed *Kinked *Deteriorated *Damaged The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM monitors vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid are turned on, allowing engine vacuum to draw a small vacuum on the entire evaporative emission system. After the desired vacuum level has been achieved, the EVAP purge solenoid is turned off, sealing the system. A leak is detected by monitoring for a decrease in vacuum level over a given time period, all other variables remaining constant. A small leak in the system causes DTC P0442 to be set. If the desired vacuum level cannot be achieved in the test described above, a large leak or a faulty EVAP purge solenoid is indicated. This can be caused by the following conditions: *Disconnected or faulty fuel tank pressure sensor. *Missing or faulty fuel cap. *Disconnected, damaged, pinched, or blocked EVAP purge line. *Disconnected or damaged EVAP vent hose. *Disconnected, damaged, pinched, or blocked fuel tank vapor line. *Disconnected or faulty EVAP canister solenoid. *Disconnected or faulty EVAP vent solenoid. *Open ignition feed circuit to the EVAP vent or purge solenoid. *Damaged EVAP canister. Any of the above conditions sets DTC P0440. A restricted or blocked EVAP canister vent path is detected by drawing vacuum into the EVAP system. The PCM turns off the EVAP vent solenoid and the EVAP purge solenoid (EVAP vent solenoid Open, EVAP purge PWM 0% ). The PCM monitors the fuel tank pressure sensor input. With the EVAP vent solenoid open, any vacuum in the system should decrease quickly unless the vent is blocked. A blockage is caused by the following conditions: *Faulty EVAP vent solenoid (stuck closed). *Plugged, kinked, or pinched vent hose. *Shorted EVAP vent solenoid driver circuit. *Plugged evaporative canister.

Good luck shoretex, hope this helps...please take time to rate me a fixya.

Jul 20, 2009 | 2001 Dodge Dakota

Not finding what you are looking for?
2007 Hyundai Accent GS Hatchback Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...