Question about Cars & Trucks

Open Question

Product manuel for mossberg new haven 600AT 12 gauge

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Just bought an 835 pump foerarm loose and wobbles is that normal ita a 12 gauge mag


assume this is a Mossberg. All pump shotgun forearms wobble from side to side and feel loose. As long as it functions properly (loads and ejects shells), nothing is wrong.

Nov 23, 2016 | Cars & Trucks

2 Answers

How I switch of my oil light,staying on after filling up?


The Change oil light reset instructions are in the owners manuel, some use a button located in the fuse panel, some have a status button you scroll and the use a reset button on the dash depending on make, year and model.

Dec 12, 2015 | Cars & Trucks

1 Answer

How do I fix my gauges? (Ie, gas gauge, temp gauge, speedometer, odometer)


Fuses? Blown fusible link? Most gauges work by getting 12 volts from the ignition switch when on, and getting a ground from the sender. Often the 12 volt supply wire goes to more than one so if dead, both will fail. If you have a wiring diagram, you might find which wire to cluster should be hot, and trace it backward to find the issue. Easier to check for ignition switch feed first.

Jul 01, 2015 | Cars & Trucks

1 Answer

So I removed the AC compressor and hoses because it seized and I haven't bought a new one yet. This is for my 1994 Camaro 3.4L V6. Now when I start the car all my gauges flicker and car almost...


Are all of the wiring harness connections good ? Is the alternator turning in the correct direction ? And is it charging the battery ?
As for the temp gauge, the sensor grounds the gauge, so you may have a short to ground in the wiring harness.

Jul 15, 2013 | Cars & Trucks

2 Answers

I have a 2002 mustang and it is making a squeaking noise and the battery light comes on. Both happen intermittently but I haven't had any change in the battery gauge. Do I need a new alternator?


the sound is either the alternator belt (as in way too loose), or bad bearings in the alternator and it seizes up intermittently and the belt screeches as it slides on the pulley. your gauge is telling you the amount of voltage at the battery, but the light is a charge indicator and it is pointing you to the alternator.

Apr 04, 2013 | Cars & Trucks

1 Answer

Ob2 or what


No, your GM product is OBD I and uses an ALDL Assembly Line Data Link connector in about the same place as most newer connectors under the dash. this system is only standardized to each carmaker(GM,Chrysler, and FoMoCo). There is a way to get the two digit codes With a paperclip, but I don't remember haven't had that car(88 SkyHawk) in 12 years.

Oct 28, 2012 | 1992 Buick Park Avenue

1 Answer

Guages don't work


That could be the cluster gauge assembly itself and it may have bad connections on its circuit board or the body control module that controls the cluster gauges has a problem.

Dec 18, 2011 | 1997 Pontiac Grand Am

1 Answer

2007 Chevy silverado (classic). Once hooked up to trailer, the brake lights do not work only turn signals on trailer.


firat of all check and make sure you have a real good ground or otherwise you will lose current to another wire and this can short out and cause the lights to malfunction.

White: Ground
Brown: Running
Yellow: LT and Stop
Green: RT and Stop

This is the wiring code for the 4 wire trailers and
Wire a round seven-pin hitch, typically sold without a wiring harness, to the vehicle observing the following color codes: Run a white 10-gauge wire between ground and terminal one, run the blue 12-gauge wire between the electric brake controller and terminal two, the brown 14-gauge wire between the taillights and terminal three, the black 10-gauge wire between the permanently live 12-volt supply and terminal four, the yellow 14-gauge wire between the left turn/brake light and terminal five, the green 14-gauge wire between the right turn/brake light and terminal six and the purple 14-gauge wire between the backup light and terminal seven (in the center).

Feb 18, 2011 | 2007 Chevrolet Silverado Classic SS New...

1 Answer

Fuse diagram for 1992 Mercury Topaz


I have the manuel for the fuses. It`s for a 1992 mercury topaz. If you haven`t found one yet, if you email me I can scan it and get it too you. my e-mail is mcnedham@rogers.com

Apr 09, 2009 | 1992 Mercury Topaz

1 Answer

Speed sensor low voltage


lets do this ck voltage with voltmeter at battery post on the back of you alternator. you have to have at least 12.35 volt at least. most likely around 14.-16.. but 12.35 min. any lower replace.

hope2help

Jul 23, 2008 | 1988 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...