Question about 1999 Ford Crown Victoria

Open Question

Vibration in front end of Crown Victoria

Check engine light blinks on and off while driving, when vibration occurs.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

co7196
  • 3433 Answers

SOURCE: 1995 Ford Crown Victoria - shakes/vibrates @ highway speeds.

Alignment has alot to do with the tires not shimmying.. Like zero toe setting. Loose componants like tie rod ends and the idler ar worn. You can ck for excess front end play by holding the front and back of the wheel and pushing and pulling on it, like rocking it. OR have someone rock the steering while you watch where the play is from underneath. By rocking I mean turn the steering wheel back and forth. Look at all th joints and pivot points for excess play, which is, movement not immediate to the rest of the steering system. Tire balance is very important. Wheel hop is a sign of a bad tire and it overtaxes the shock absorber. Shocks don't cause shimmy because they are a vertical movement controlA shimmy is lateral or side to side.Wheel balance weights must be spit. If a 2 oz. weight is needed to balance the tire, Oe once should be on the inside of the wheel and one ounce on the outside directly across from each outher.. Loose wheel brgs will cause shimmy, but they would not last long. Caster setting on the wheel alignment will also cause shimmy. Like on a shopping car. too much caster causes the wheel to start fluttering and is very hard on other componants. This may be why you have worn tie rod ends and a bad pitman arm. Worn control arm bushings and ball joints directly affect titre wear and can only be feltwhen the front end hits a dip and detected by side wear on the tire edges. Summary: replace the tie rod end and have the car aligned. Good Luck, -Ned_ sorry about the book

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2007 Crown Victoria Police Interceptor vibrate when I get to 40 miles an hour and then die off back to normal by the time it reaches 50


Ford Crown Victoria Questions - what would cause a whole ...

www.cargurus.com > Questions > Ford > Crown Victoria
CarGuruswhat would cause a whole car vibration when going between 48 and 65 mph, even ... Asked by Dfranz Aug 29, 2013 at 11:53 AM about the 2001 Ford Crown Victoria Police Interceptor ... You have an open diff by turning one wheel the driveshaft should turn before the .... 2007 Ford Crown Victoria Police Interceptor For Sale.

Nov 03, 2015 | Cars & Trucks

1 Answer

VIBRATION AT 60MPH OR BETTER


try and rotate the tires if on has a problem the vibration will change to the rear

Jun 14, 2012 | 2004 Oldsmobile Alero

1 Answer

2007 Mazda CX-9 has recently developed a front end vibration under heavy acceleration. Vibration disappears if shift to neutral at highway speed, engine rev's smoothly in neutral. Suspect engine...


Try to rev the engine while at neutral if you get the same vibration to pinpoint if its from the engine or the drive shafts. If the issue occurs at a certain rev it may likely be the variable valve unit. Check if possible if you can get errors from the computer.

Sep 08, 2011 | 2007 Mazda CX-9

1 Answer

When braking I get a pulsating vibration in front. We replaced the rotors and the pads but the problem is still there. What could be causing it? I was told that the rotors I got were a lower brand thus the...


It may not be the rotors, it could be a worn suspension component, loose ball joints, tie rod ends, worn control arm bushings. When you installed the new rotors and pads and the problem was still there on the first test drive, than it is not the rotors or pads causing the pulsing vibration.

May 07, 2011 | 2000 Ford Crown Victoria

1 Answer

Stering wheel shakes at 30 to 40 miles an hour


Put your spare tire on one side of the front. Drive it, if it does not help, replace the spare and then try removing the other front tire. Drive it and see if it helped.

The tire that caused the vibration probably threw a weight or has a broken belt. Have that tire checked and repaired, then have the Tire shop put the spare back in the trunk.

If it is not a tire problem check your tierod ends. They connect both front wheels and if there is a lot of play, you can get shake and wobble from the slack in the frontend.

Sometimes front Rotors can cause a shake when you hit the brakes. If the car shakes without pressing the brakes, then its the tires or frontend.

Feb 07, 2011 | 2004 Ford Crown Victoria

1 Answer

1995 Ford Crown Victoria - shakes/vibrates @ highway speeds.


Alignment has alot to do with the tires not shimmying.. Like zero toe setting. Loose componants like tie rod ends and the idler ar worn. You can ck for excess front end play by holding the front and back of the wheel and pushing and pulling on it, like rocking it. OR have someone rock the steering while you watch where the play is from underneath. By rocking I mean turn the steering wheel back and forth. Look at all th joints and pivot points for excess play, which is, movement not immediate to the rest of the steering system. Tire balance is very important. Wheel hop is a sign of a bad tire and it overtaxes the shock absorber. Shocks don't cause shimmy because they are a vertical movement controlA shimmy is lateral or side to side.Wheel balance weights must be spit. If a 2 oz. weight is needed to balance the tire, Oe once should be on the inside of the wheel and one ounce on the outside directly across from each outher.. Loose wheel brgs will cause shimmy, but they would not last long. Caster setting on the wheel alignment will also cause shimmy. Like on a shopping car. too much caster causes the wheel to start fluttering and is very hard on other componants. This may be why you have worn tie rod ends and a bad pitman arm. Worn control arm bushings and ball joints directly affect titre wear and can only be feltwhen the front end hits a dip and detected by side wear on the tire edges. Summary: replace the tie rod end and have the car aligned. Good Luck, -Ned_ sorry about the book

Sep 24, 2009 | 1995 Ford Crown Victoria

2 Answers

Severe vibration and knocking sound!


sounds more like a ujoint or a center support for the drive shaft. also check and make sure that the flywheel bolts have not come loose. also check the harmonic balancer and make sure it is not seperating

Aug 23, 2009 | 1996 Ford Explorer

1 Answer

Are front side marker lights suppose to blink


They are NOT supposed to blink only the front facing

Apr 04, 2009 | 1999 Ford Crown Victoria

1 Answer

Check engine light on


When the check engine light flashes this is a class a misfire. If this is a 1999 you have a spark plug or a spark plug wire bad. Get a tune up done and replace plug wires.

Aug 14, 2008 | 1999 Ford Crown Victoria

1 Answer

1999 Ford Crown Vic transmission problems


check u joints and drive shaft for weights hope this works

Aug 09, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...