Question about 1990 Mercedes-Benz 190

Open Question

Mercedes 190 pierburg 175cd carb

Hi i need to locate the mixture screw on my 1989 190 is it below the carb, there is some sort of solonoid there with wires attatched do i need to disconnect wires undo the 22mm nut and screw the solonoid in or out it has just failed the emmissions giving a reading of 7.5 c/o you help would be much welcome kind regards ian

Posted by on

6 Suggested Answers

alicantecoli
  • 21949 Answers

SOURCE: carb mixture screw ineffective

flexable pipe from manifold to fixed pipe for the brake servo its porous and sucking in air

Posted on Jan 10, 2009

  • 18 Answers

SOURCE: where do you locate oil filter on a 2003 mercedes c180

KOMPRESSOR ENIGNE?? IF SO CHECK BY THE FIREWALL DRIVERSIDE. ITS A THIN FILTER CAP , HAS A BLK 27MM PLASTIC ALMOST NUT TO REMOVE OIL FILTER.

Posted on May 19, 2009

michigan man
  • 3533 Answers

SOURCE: Front Suspension ball joint.

give these websites a try www.autozone.com if they have you car listed you be able to get pictures and diagrams showing you how to repair your car if you have a autozone near you there you can rent the special tools you need then take it back and get your money back and here is another website for more repair information www.alldatadiy.com

Posted on May 24, 2009

taran_2005
  • 10515 Answers

SOURCE: need to locate fuel filter on 1989 mercedes benz

Hi,

The fuel filter is located on the right rear underside of the car, just ahead of the rear axel area. You need to remove the cover to find it. It is the large canister next to the electric fuel pump.

Thanks.

Posted on Jun 18, 2009

Obertelli
  • 3006 Answers

SOURCE: dashboard on a mercedes 190

Sorry, but removing the entire dashboard on a Merc 190 is far too detailed and involved to go into on this site, especially as it's very time consuming to scan and upload to a website all of the photos and diagrams which you'll need. In any case, it's all copyrighted material and so would be illegal to do so.

I respectfully suggest that you get a Haynes manual; the first repair alone will more than pay for the book.

Posted on Jul 10, 2009

Sandroid
  • 15 Answers

SOURCE: how to install new water pump on 1989 mercedes 300e

Drain the coolant
Remove air cleaner assembly
Disconnect water hoses from radiator
Remove drive belt
Remove power steering pump
Remove water pump drive pulley
Loosten hose clamps on cylinder head tp water pump cooling line
Remove water pump mounting bolts and water pump

Just reverse these procedures to install new pump.



Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you show me a video how to remove and replace a coolant temperature sensor to a mercedes 1989 190E 2.6 6-cyl


Two types were used .On this engine ,but not both together. One was round wth 4 round contacts inside ,And one that is colured green, i think if i am right .This has two contacts .Both on the top of the block on the inlet side of the head at the back.Removal is just to unscrew to extract it, If your not sure and dont know get firther help .

Oct 02, 2016 | 1989 Mercedes-Benz 190

1 Answer

Does 1989 190 mercedes have chip in key


No, Mercedes 1989 model does not have chip. We have made a key for E Class and even made a video for it...

Sep 28, 2013 | 1989 Mercedes-Benz 190

1 Answer

Where is the fuse box on a 1989 190D Mercedes located?


The fusebox is located under the bonnet at the rear of the right/hand wing, the lid unclips and has the fuse listing on the underside. Please make sure the lid is replaced correctly, as water will soon cause relay and fuse problems.

Jul 12, 2011 | 1989 Mercedes-Benz 190

1 Answer

Hot air from defrost and cold air from center vents when turn on ac in 190-e 2.6 mercedes benz 1989' help please


I haven't got the problem solve as of yet, I have a 190-e 2.6 mercedes benz 1989 not a e300 still checking different mech your insight give me much help and Im gratful for everyone for their good advice.

May 11, 2009 | 1994 Mercedes-Benz E-Class

2 Answers

ON'T LAUGH BUT I CANNOT FIND THE HOOD LATCH!


The hood latch is located near the driver's feet, flush with driver's side wall, beneath the dash on the left hand side. It's a black, plastic latch that is shaped like a hook. After you've pulled the latch, a small latch should pop out on the left hand side of your grill. Pull the latch further out (towards you) and lift the hood with your other hand. Do not try to pull out and lift with the latch, you'll break it off.

The front headlight is easy to replace--it should be self explanatory. The directions for replacing the headlights should be in your driver's manual that comes in the glove box--it's like that for mine. Otherwise, I would look into finding a copy of the repair manual online on ebay or something, that's where I found mine for my '91.

I'm not sure enough about the rest to give you advice--sorry!

Feb 01, 2009 | 1989 Mercedes-Benz 190

1 Answer

How do I replace the heater blower motor on a 1989 190e


Hello, The blower motor is located below the windshield wiper assembly. You have to remove the plastic cover that below the windshield then remove the wiper assembly, then you will see the blower housing. Remove the screws from the housing then remove housing cover. Look close because some of the screws are hard to see. Once you get the cover off, you will see the motor and there is a metal strap that holds it down. Take a punch or whatever and stick it in hole in the strap and push down. Then the motor will come out.
I hope this helps.
CYA, Gator241

Jan 06, 2009 | 1989 Mercedes-Benz 190

1 Answer

BLOWER MOTOR MAKES NOISE.


Hello, The blower motor is located below the windshield wiper assembly. You have to remove the plastic cover that below the windshield then remove the wiper assembly, then you will see the blower housing. Remove the screws from the housing then remove housing cover. Look close because some of the screws are hard to see. Once you get the cover off, you will see the motor and there is a metal strap that holds it down. Take a punch or whatever and stick it in hole in the strap and push down. Then the motor will come out.
I hope this helps.

If you find this information to be correct would you please enter a "fixya" rating.
Thanks, Gator241

Dec 11, 2008 | 1989 Mercedes-Benz 190

1 Answer

Carb mixture screw ineffective


flexable pipe from manifold to fixed pipe for the brake servo its porous and sucking in air

Aug 10, 2008 | 1986 Volkswagen Wagon Camper

Not finding what you are looking for?

Open Questions:

See all 1990 Mercedes-Benz 190 Questions

1990 Mercedes-Benz 190 Logo

Related Topics:

1,134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...