Question about Cars & Trucks

1 Answer



Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

5th Avenues have an electricronic control module that controls signal to the coil. Check coil to see if you are getting fire from there, if nothing out then check connector to see if signal is coming in to coil. if not- replace the ecm.

Posted on Jan 12, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced crankshaft sensor on a 94 jeep ans still no spark

I just posted 1min ago to 93

why guess, crank and get the scan codes?
the ECU will in fact telly you when any of the 3 permissive fail.

Mar 02, 2014 | 1994 Jeep Cherokee Country

2 Answers

What does a crankshaft sensor do? what does a camshaft sensor do?

get a HAYNES repair manual, tells you what all sensors do ! the crankshaft sensor sends info to the SBEC, reguarding engine crankshaft position. the camshaft sensor reads camshaft position, sends a coded signal to the SBEC, which uses this info to determine whether the fuel injectors and ignition coils are correctly synchronized !

Feb 14, 2013 | Chrysler Sebring Cars & Trucks

1 Answer

Car cranks and then stalls out within seconds, Had been running great, just started doing this.

The SBEC is the computer for the engine.
I would check the auto shutdown relay and ignition module first. You need to know if you are loosing spark to the plugs or fuel to the injectors to know how to proceed.

Aug 09, 2012 | Dodge Cars & Trucks

1 Answer

Overheated engine with belt off but still ran rough when shut down. About 1 gallon fluid steamed out. Engine turns over but no spark. Fuel pump operates. Engine code 12 showing. Coil is good and so is...

if its a 2.2/2.5 wiggle the wiring at the base if thedistrubutor while checking for spark,if you have spark it is a fauty pick up undet the distributor cap.Open the oil filler cap and ck for a milky substance the if it is evidend you mostlikly have damakedthe head gasket.

Feb 26, 2011 | 1992 Plymouth Acclaim

1 Answer

Is their a fuelpump reset button on my dodge dakota pickup 4by4 3.9 (le)

The Fuel Pump is controlled by the SBEC Controller through the Auto Shutdown
Relay (ASD). For testing purposes and using an Enhanced Scan Tool, both ASD and Fuel Pump operation can be easily tested.
Also, the Single Board Engine Controller (SBEC) WHEN Ignition Switch is in the
RUN position, requires a distributor reference signal or it will de-energize the ASD.

Dec 26, 2010 | 1991 Dodge Dakota

1 Answer

My 89 dodge dynasty has no spark. ive put in 2 new coils, and swapped out the ASD relay n SBEC w new ones but still nothing. if i jump 12v directly to pos on coil still no spark but my fuel pump will...

sounds like the fuse box is not sending volts to the coils check the fuses and check the line to the coil packs make sure there getting power hope this helps

Sep 24, 2010 | 1989 Dodge Dynasty

2 Answers

How do I change Spark plugs?

93 park ave has a v8. Four plugs on each side. Followthe spark plugs from top of engine to spark plugs. Use a spark plug wire remover (plastic pliers) to help remove wire from plug. Mark each wire where they go. Go down to auto store and buy pugs and get a swivel spark plug wrench to fit the plugs anduse a extension with rachet to remove plugs (turn counter-clockwise to remove). Replace with new. (new plugs should screw in with fingers, then tighen with socket firmly. Not over tight. I holp this helps a little - ran out of writing space. Good luck

Oct 15, 2009 | 1993 Buick Park Avenue

1 Answer

1991 5th ave fault code 62

62 is basically a failed attempt to update service reminder indicator miles in the PCM memory.(eeprom) So you won't get a service reminder, wouldn't bother me, especially if no light on or anything. perhaps dealer could store it, but why bother?

Jun 10, 2009 | 1991 Chrysler Imperial

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides