Question about 1987 Ford Ranger

1 Answer

I have a 1993 ford ranger xlt and i need to change the altenator

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

Go to Autozone website and key in info about vehicle. Make sure you know whether it is 2.3, 3.0, or 4.0 motor. Picture of part will show you where mounting bolts are located as well as location of "hot" wire connection and pigtail. Remember to disconnect the battery before you do anything to the electrical system. Website also has a how to on replacing this part. Good luck!

Posted on Jan 12, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dhorsefield
  • 286 Answers

SOURCE: brakes seized on ford ranger

A drum brake shoe lining may have become separated from the metal pad that holds it in place and will cause the wheel to lock. The only repair necessary is to replace the brake linings with new ones. The loose piece of brake lining, if this is the cause, will not likely cause any difficulty removing the drum.

Posted on Jul 25, 2010

ZJLimited
  • 17970 Answers

SOURCE: I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED

For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Posted on Jul 27, 2010

muntejaya
  • 10421 Answers

SOURCE: need wiring diagram for a 2001 ford ranger xlt 3.0

Hi there, Is this diagram address your request?3461bb6.gif

Posted on Aug 10, 2010

  • 2841 Answers

SOURCE: I need a surpintine drive belt diagram for a 2000

Here you go: clay58_22.png

Posted on Feb 04, 2011

Testimonial: "thank you"

jturcotte
  • 8273 Answers

SOURCE: i need wiring diagram for 1995 ford ranger XLT i

Unfortunately this model has separate filaments for the stop and turn signals. You will need to use an adapter relay to hookup a standard trailer plug or you will need a trailer that also uses this wiring setup. The first diagram below indicates there my be a trailer adapter for the turn signals at the base of the steering column. The wire colors at the bulbs are as follows:
tail/running lights: brown
stop: light green
left turn: light green/white stripe
right turn: white/light blue stripe
back up: black/pink stripe
ground: black

Please let me know if you have questions.
10_8_2011_12_03_28_pm.gif





10_8_2011_12_04_46_pm.gif10_8_2011_12_05_06_pm.gif10_8_2011_12_10_51_pm.gif

Posted on Oct 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the powertrain control module located ON MY 1993 ford ranger xlt 4.0 4x4


ive had this question before. It is under your center console where the cup holders are. up tworge the front, take the console off and you will see it a little square box silver in color with a wire harness plugged into it. hope i helped.

Jan 06, 2015 | 1993 Ford Ranger SuperCab

1 Answer

How do I change the cabin filter in my Ford Ranger xlt 2011


Check with your Ford dealer. As far as I know Ranger was normally not equipped/supplied with a Cabin Air Filter.

Dec 21, 2014 | 2011 Ford Ranger XLT

1 Answer

I have no key to my 1993 ford ranger xlt 4.0 Auto 2wd Ignition switch removal and Installation


In most cases you will have to drill it.
There are videos on Youtube that show how its done.
Most all Ford locks in the late 80s and early 90s are the same style.

Aug 03, 2012 | Ford Cars & Trucks

1 Answer

Where is the pcv valve located on a 1993 ford ranger xlt 2.3L ?


I'll do my best to explain. The PCV is located center, upper engine area, driver side of engine, between engine block and intake manifold, mounted in vacuum hose. I hope you got that and that it helps you. Good luck.

Mar 24, 2011 | 1993 Ford Ranger SuperCab

1 Answer

Car Wont Start It May be the Starter Where is it on a Ford Ranger 1993 Xlt I had a Mechanic Hit it But I Dont Know Where or How


the radio turns on and thats about it. I thought it was the battery because it won't turn over but there is a little bit of juice in the battery.

Jan 03, 2010 | 1993 Ford Ranger SuperCab

1 Answer

How do i aim the headlights on my 1993 ford ranger xlt 4x4


the adjustment screws are there u just have to look hard for them.
one on bottom up/down one on the side side to side.

Oct 02, 2009 | 1993 Ford Ranger SuperCab

1 Answer

How do i change a pcv valve on a 1993 ford ranger xlt 4.0L


Hello there:
first off make sure you have the right one for the truck.
Now just pull the old one off of the valve cover and remove it from the hose and insert the new one than reinsert it on the valve cover and you are done.

Aug 10, 2009 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...