Question about 2005 Renault Megane Scenic

Open Question

Renault scenic II inlet manifold removal

How to remove renault scenic intake manifold

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 4044 Answers

SOURCE: renault scenic drivers electric window motor runs

The track guide that operates the window from the motor is damaged or has jumped track. Remove the inner door panel and operate the window and see which has happened. If it has jumped track check for missing or damaged guide retainers if it is damaged or broken replace it. Normally runs about $15 to $20 for the part. Now if the drive guide is not damaged and it is still not working the gear that drives it is damaged and you will need to replace the motor as this is pressed on and not user replaceable. Good Luck

Posted on Sep 12, 2009

Ad
  • 1986 Answers

SOURCE: inner door panel removal, renault megane scenic

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

  • 2 Answers

SOURCE: My Renault Megane Scenic S reg heater is not working

Most likely to be a faulty resistor block, which has 3 resistors and a thermal fuse controlling fan speeds 1,2 and 3, maximum speed 4 by-passes the resister block. It may also be poor electrical connections to the resistor block caused by overheating. Renault ask for approximately £350 to carry out repairs, a replacement resistor block will cost £50. If you decide to carry out the repairs yourself, be advised that if you are not competent to carry out such work you, could cause electrical damage or worse an electrical fire.

Posted on Nov 14, 2009

  • 1 Answer

SOURCE: I have a renault scenic expression+ 2002, my rear

I have noise from cam/other belts on my scenic 1.6 2002

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcv valve on a renault scenic ii 1.6vvt 2004


The PCV valve lives in the breather pipe going between the inlet and the crankcase and is usually well hidden. Disconnect the breather pipe from the inlet and slide a stiff piece of electrical wire gently down and that hopefully should give you an idea of its exact location.

May 30, 2016 | Renault SCENIC Cars & Trucks

1 Answer

Back window on 05 senic gone down and wont go up...is this a fault and how do i get it bck up..


Scenic II Drivers side Electric Window has a mind of its own ...

www.renaultforums.co.uk > ... > Ask the Experts > Electronics

Mar 16, 2010 - 82 posts - ‎34 authors
I managed to get the window back up using the Fuse 40 trick, so it is now up, but it no longer works on the switch. ... My drivers side window on my scenic 04 has gone down and wont do anything, my ... Hi, Window played up once before, ie went downand wouldnt go back up! ..... My scenic is a June 2005. scenic electric window fault
11 posts
Apr 11, 2010
Scenic II - window has gone down and stuck
23 posts
Feb 23, 2010
Renault Megane - Window FUBAR?!!!
51 posts
Jul 28, 2007
Electric window problem
23 posts
Sep 7, 2005
More results from www.renaultforums.co.uk

Is your Renault Window fault driving you crazy? - The easy ...

? 3:14
https://www.youtube.com/watch?v=vcdULQXKcek
Nov 18, 2012 - Uploaded by QERutube
If, when pressing the up/down window switch, the motor can be heard to be .... my car window goes down but ...

Renault Scenic 2 window problems & door panel removal ...

? 8:17
https://www.youtube.com/watch?v=y7NlPFwW540
Feb 16, 2013 - Uploaded by Secluded Dell
Taking off the driver door panel to get at the window regulator motor controller and window clip. ... out ...

Nov 28, 2015 | Cars & Trucks

1 Answer

Where is air temp sensor megane scenic 2.0 located


It is usually located on the inlet manifold on the 16v model.

Jul 29, 2014 | 1999 Renault Megane

1 Answer

Renault scenic wipers and park lights stay on


Try removing the plastic trim on the steering column, pull off the multi pin plugs on the stick switches and see if that stops them. May be the switch is the cause?

May 22, 2014 | 2005 Renault Scenic 1.9

1 Answer

I can't find the egr valve on our renault scenic 1.6 year 3


Only one place it could be is on the intake manifold, cause that is where it directs the exhaust gas it receives back into the engine.
If you look on the exhaust manifold, or on the exhaust pipe just below it, you should see the small metal tube that diverts a small amount of exhaust back to the egr valve. The controls for the egr can vary a lot from year to year, so appearances may change, don't give up and you'll find it.

Dec 26, 2013 | 2006 Renault Scenic 1.6

1 Answer

How do you remove the fuel injectors in a 1988 bronco with a 351?


  1. Remove the upper intake manifold. Be sure to depressurize the fuel system before disconnecting any fuel lines.
  2. Disconnect the fuel supply and return line retaining clips.
  3. Detach the vacuum line from the fuel pressure regulator.
  4. Disconnect the fuel chassis inlet and outlet fuel hoses from the fuel supply manifold.


0900c15280078008.jpg

Sep 17, 2010 | 1988 Ford Bronco II

1 Answer

How to remove the intake manafold cover to get to the spark plugs


need more info, what size engine? what model need that to send u the correct RnR of the upper plenum

here is the 3.5L version of removal:
  1. Disconnect and isolate the negative battery cable.
  2. Disconnect the Inlet Air Temperature (IAT) sensor electrical connector
  3. Remove the air inlet hose from the throttle body.
  4. Disconnect the Manifold Absolute Pressure (MAP) sensor electrical connector.
    1. Disconnect the PCV hose ,purge hose and power brake booster hose from the upper intake manifold.
    2. Disconnect the electrical connector from the electronic throttle control .
    3. Remove the fasteners from the throttle body and cylinder head and remove the throttle bracket.
    4. Remove the wiper module, strut tower support and EGR tube
    5. Disconnect the electrical connectors from the manifold tuning valve
      1. Remove the fasteners , from the intake manifold support brackets.
      2. Remove the upper intake manifold retaining bolts, insulation foam pad and manifold. Clean all gasket sealing surfaces.

Sep 02, 2010 | 2006 Dodge Charger

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

2 Answers

I have 2 leaks on my renault scenic, one comes in


why is wet came from inside driver floor inside box store there is water was inside car model ireuault scenic 2004

May 12, 2010 | Cars & Trucks

4 Answers

Emissions warning light on Renault Grand Scenic II, 2004 1.5 DCi


i have a renult scinic 2004 1400cc emissions warning light on running uneeven and loss of power can this be sorted out what is it

Nov 25, 2008 | 2000 Renault 181

Not finding what you are looking for?
2005 Renault Megane Scenic Logo

Related Topics:

574 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

xxxxxx xxx

Level 3 Expert

4915 Answers

yadayada
yadayada

Level 3 Expert

78238 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...