Question about 1990 Mazda MPV

1 Answer

93' mazda mpv , wiper control lever will not turn off wipers.

I'm picking a used wiper control. I know I have to pull off the steering wheel. What are the steps to taking off the steering wheel to get to the controls and do I need any special tools.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Study THe steering wheel look for Philips screw holes, that removes horn cover front, on back of steering wheel, once you take the front cover of the steering, do not loose any springs and screws, use the cars ashtray to collect parts, Looking at the front, You will see a NUT 22 mm or 19 mm grab a 1/2 pride bar with socket( with locked steering) anti clock wise loose nut and washer and remove them, after that tap steering wheel from back towards You with both hands at the same time, till wheel OFF, You will see the wiper control leveler and how to replace it

Posted on Jan 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper switch replacement on 1996 lexus ls400


According to the THIRD wiring diagram on the
BBB INDUSTRIES FREE circuit drawings and
TECHNICAL SERVICE BULLETINS...

(registration required (these are real documents))...

You can disable the "airbag squibs" by pulling
SPECIFIC fuses out of the AIRBAG SENSOR ASSEMBLY...

I will not quote the FUSES... because TOYOTA is
quite famous for playing their TECHNICAL DATA
close to their vests... (my opinion).

However you will be happy to know the WIPER SWITCH
shows as AVAILABLE 20 years later (obviously popular)
((even on AMAZON))...

Hope this helps!!

1996 LEXUS LS400 4 0L V8 Wiper Washer Switch RockAuto

More Information for AIRTEX WELLS 1S9683

Carnac the Magnificent

May 20, 2017 | Cars & Trucks

1 Answer

How do you remove the steering wheel from a 1974 Super beetle?


hi there,this is all i could find on the internet.
this should show you how to do it.just scroll down on the page and you will see (steering wheel removal.
hope this is for you car.
Steering Column Work
or this one.
Help Just got beetle and need help removing steering wheel beetle

Nov 29, 2017 | Volkswagen Beetle Cars & Trucks

1 Answer

Just bought a used 1990 keep wrangler. The turn signal k arm on the steer wheel is missing. Is the windshield wiper control on the turn signal arm as well? I do not see a place to turn on the wipers


just get one from a junk yard to remove it just push turn and pull the only thing is that if the car has cruise control you got to cut the wire... and to install it your car push in and turn wiper will work signals but no cruise control unless you go trough steering coloum

May 01, 2012 | 1990 Jeep Wrangler

1 Answer

The windshield wiper switch on my 2001 lumina needs to be replaced and I am thinking of doing it myself. How hard is it to do this? Is it true that I would need to take the steering wheel off?


No , the steering wheel doesn't need to be pulled off . The wiper switch just pulls out of the steering column .

Verify that the lever (2) is in the center of the OFF position.
Disconnect the electrical connection (3) behind the lever (2).
Remove the switch lever (2) by pulling straightly outward on the lever .

Nov 25, 2010 | 2001 Chevrolet Lumina

3 Answers

2002 mazda mpv, key stuck in ingition and it is in park , but the key wont turn all the way to lock, it will only go as far as acc?


Mazda MPV have problems with failing gear shift change assembly ( includes park sensor micro switch)

Pull the fuse for the hazard lights ( 10amp) - if the key comes out, then the switch is defective.

Fix the problem by installing a new change lever assembly - part number for 2000 and 2001 MPV's is LC62-46-10XE with MSRP of $246.90. 2002-2004 would be a LD47-46-10XB with MSRP of $250.40.

May 23, 2010 | 2000 Mazda MPV

1 Answer

Some times wipers would come on with out turning on the wiper switch and now will not turn off at all


Sounds like a bad wiper switch assembly.

Removal & Installataion
  1. Disconnect the negative battery cable. Remove the steering wheel.
  2. On vehicles equipped with tilt wheel, remove the tilt lever.
  3. On vehicles equipped with tilt wheel, remove the steering column collar by pressing on the collar from the top and bottom while removing the collar.
537bccf.gif
To remove the tilt column control lever, simply rotate it counterclockwise until removed

4ab784d.gif Exploded view of the combination switch mounting and column related wire harness connectors


  1. Remove the instrument panel trim cover retaining screws. Remove the trim cover.
  2. Remove the 2 screws from the bottom of the steering column shroud. Remove the bottom half of the shroud by pulling the shroud down and toward the rear of the vehicle.
  3. If the vehicle is equipped with automatic transmission, move the shift lever as required to aid in removal of the shroud. Lift the top half of the shroud from the column.
  4. On 1991 automatic transmission equipped models, disconnect the selector indicator actuation cable by removing the screw from the column casting and the plastic plug at the end of the cable.
  5. Remove the 2 self tapping screws that retain the combination switch to the steering column casting. Disengage the switch from the casting.
  6. Disconnect the 3 electrical connectors, using caution not to damage the locking tabs. Be sure not to damage the PRNDL cable.
  7. Installation is the reverse of the removal procedure. Torque the combination switch retaining screws to 18-27 inch lbs. (2-3 Nm).

Oct 26, 2009 | 1999 Ford Ranger SuperCab

1 Answer

The winshield wipers and steering wheel not working properly


Sounds like the wiper lever is broke on the inside of the colum.

May 18, 2009 | 2002 Lincoln LS

1 Answer

Wiper controls


Sorry but the 1989 deville wiper switch is controlled by the turn signal lever on the left of the column.

May 16, 2009 | 1989 Cadillac Sedan DeVille

1 Answer

Instructions for turning on back screen wiper on Ford mondeo 1.8


2 ways this could work. 1 is by pushing the wiper switch towards the dash.

2nd is when you pull the lever towards you, it will turn the intermittant wipe on, pull it towards you again to cancel.

TL

Jan 12, 2009 | 1999 Ford Contour

Not finding what you are looking for?
1990 Mazda MPV Logo

Related Topics:

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...