Question about 2005 Peugeot 405

1 Answer

Knotting i have a knotting in the back right hand side of a peugeot 406 98 not the shock or spring

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 250 Answers

U mean knocking, this is common, there is a little tie rod, top of hop about 5 inches long, hes worn out, about £20

Posted on Aug 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Truck leans 1/4 on right side. What I have done.. I installed new bushings to entire vehicle and also installed all new shocks Front and Back. Specs and torque are in place. Question is... Why would in the...


Hate to break it to ya but your frame might be bent. If one side is bent downwards it will force front and back tires away from each other causing the truck to be lover on one side.

Apr 10, 2017 | Chevrolet Chevy Cars & Trucks

1 Answer

My Peugeot 407 front right wheel area creeks like mad as I set off, break, turn. Just had track rods done but still occurs as before. Suspension rusty/dry? It's a 58 plate saloon!


Most likely a shock, spring or something with front suspension. What is happening is the suspension components can't move freely and therefore are creaking

Jun 03, 2016 | Peugeot Cars & Trucks

2 Answers

Astro van suspension


What the back is to low or left and right side not even if you whant to lift the rear suspension air shocks

Apr 05, 2012 | 1998 Chevrolet Astro Van

1 Answer

Is there any difference on the coil spring between avantgarde and elegance/classic model? I had my right side changed only due to cost wise but it seems there is a difference of gaps (wheel housing and...


You do not say if you had the shock absorber changed at the same time..Springs normally break due to the shock absorber losing hydraulic fluid and the spring has to take all the force of any normal impacts from the road.ie pot holes and bumps.. In all cases it is best to change both the coil spring and shock absorber on both sides just to avoid the problem you are describing. i am certain your garage would have fitted the correct item(s) for your model.

Jun 18, 2011 | 2002 Mercedes-Benz C-Class

1 Answer

Replacing the shocks & struts


If your not very mechanically inclined , Its best & safe for you & others not to try to change out struts. But if you are inclined, then this is what you need to do the job. Struts are shock absorbers that are inside of a highly compressed spring. You will need spring compressors that you can buy or rent at your local auto parts stores. You need to compress the spring before removing the center shock. If you do not compress the spring sufficiently the shock can come out at a high rate of speed causing injury to you & others. You will need to compress the spring from both sides, ( opposite from each other ) if you install a spring compressor on one side just put the other tool right across from it on the same spring. compressing the spring evenly on both sides. Not all at one time just on one side of the spring. After doing so remove the top & bottom nuts of the shock. Your rented or bought spring compressor should come with directions & illastrations to better assist you with the job. Good Luck.

May 08, 2010 | 2002 Honda Accord

1 Answer

Remove window winding handle on peugeot 106


There is a horseshou shaped spring clip under the handle, between it and the trim pad or washer if fitted, a thin ribbon with a small knot run behind can flick it off or a special tool made by draper from a motor factors might be easier.

May 06, 2010 | 1991 Peugeot 405

1 Answer

Ive got coolant water coming out as fast as i put in my 206 gti


Freeze plug, head gasket, hose to the heater core. You have to get back there and look.

Feb 06, 2010 | 2005 Peugeot 405

1 Answer

98 toyota tacoma tipped on the left side


the weak spring is making it tip. also you say the other shock is leaking fluid. you need to replace both shocks and springs, the seem to have been worn down, there is no fix other than using spring blocks to boost up the saging side, but i would recommend replacing it all.

Nov 30, 2009 | 1998 Toyota Tacoma

2 Answers

Stabler at high speeds


...the easy ways are...change the shock absorbers to hard with gas filled not oiled filled...change the tires to 185 x 60 x 15" change and lowering the spring...if you can then add front, sides spoilers and wing spoiler...

May 15, 2008 | 1983 Peugeot 504

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...