An expert who has achieved level 3 by getting 1000 points
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
An expert that got 20 achievements.
An expert that got 10 achievements.
Re: ford focus-99 abs module
If the ABS system is functional u will have no ABS warning light showing in the dash except when u first turn the key on, that is a prove out to show the indicator light is working. If the ABS has a problem of any kind the light will always stay on when driving and the system will be disabled..
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Maybe a short in the light circuit or in the cluster..If you can communicate with the abs module and it tell you there is no codes then the module is probably ok..A code reader will not show you codes..You have got to have a scanner that will read more than engine codes to read the abs system..
Had the same thing happen after I bought my 03 Windstar. Dealer installed a new ABS module and same thing happened again,, Turns out they had to install a 2nd new module, 1st one was bad.. Toyota was doing the work, but they were sending it to a Ford dealer to tell them what to fix.
when the ABS light stays on it means there is a fault present in the ABS system and the ABS has been disabled, as long as the light is on u just have regular brakes with no ABS, there are many thinbgs that can turn the light on, most common is one of the wheel speed sensors is defective, since these sensors are about $75-100 each and there are 4 of them guessing is a poor idea, so what u need to do is have the ABS systwem tested, there will be a fault code present to help narrow down the defective part or wiring.
If you paid good money to have it fixed at a FORD AGENT then take it back and tell them that you are going to wait for it and dont take any **** from them as all work done by a Ford agent will be under warranty so if its still in warranty time take it back, or tell them your take it to the papers and let them tell the world..
It works belive me.
Let me know how you get on . RON
have a mechanic check out the 1of 3 things.1st- abs rings. 2nd- the the speed sensor or so called abs sensor's.These read off of the abs ring to make the abs brakes work! If not any of those i would say abs module.module isa little expensive though so if it is look for it on ebay or rock auto..hope i could help you?
John, My 99 F150 had an abs light on and I found the right side front wheel sensor wire had fallen off of the inner fender mount and burned the insulation and grounded the wires together, I taped up the wires and tied it up and the light went out. Your ABS module is located directly beneath your air cleaner next to and just above the steering gear box. It is black plastic and silver alumnium. Says Kelsey-Hayes right on and has six brake lines attached to it. As for the rear brake take that drum off again and have someone help by pushing the brake pedal down while the drum is off press lightly and very slowly, verify that the brake cylinder is moving, do not push hard and fast as it will probably blow the pistons out of the cylinder! If is is frozen replace it and bleed and it should be fine. The brake light is probably on for low fluid. Let me know how it goes.
read your owner manual to see when the BAS light should be on during "prove out." Sometimes the prove out is after the engine starts.
Also, if the ABS ever fails, you always still have regular power brakes.
You should go on a gravel road and slam on the brakes to se if the anti'lock still functions. You will hear the BAS motor run and the pedal pulse. good luck