Question about 1996 Ford Taurus

1 Answer

Hydraulic master cylinder.no parts in australia according to ford who can supply same.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Send me your link an you can get parts tj

Posted on Jan 12, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 279 Answers

SOURCE: where is the electro hydraulic valve on a 1991

under the drivers side on the inside of the frame rail

Posted on Jan 21, 2010

  • 2309 Answers

SOURCE: how do you remove the

seems to me that some of these were permanent connections, i may be wrong

Posted on Oct 24, 2010

  • 1 Answer

SOURCE: how do you remove a

if this is an older truck like mine the slave cylinder is internal, inbettween the trns housing and the bell housing. go under driver side of vehicle, stick your arm up in bettween the trans tunnel and the trans where the line comes down and you should feel the end of the line and the bleeder valve for the slave cylinder. at the bottom of the line there will be a clip, if u cant grab it, get something with a strong hook on the end, hook the clip and pull, ( tip) watch out for the fluid comming out it will hurt if you get that in your eyes.

Posted on Jan 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a ford fiesta 1.4i 1998 have a hydraulic clutch


If there is a second master cylinder similar to the brake master cylinder then there is a hydraulic clutch

Feb 12, 2017 | Ford Cars & Trucks

1 Answer

How to diagnose whether the clutch master or slave cylinder is my problem on 2002 ford focus 2.0 liter.Clutch pedal goes to the floor with no resistance.Brake master has fluid.


could be either
the problem is air in the hydraulic system either form a leaking slave cylinder or a faulty master cylinder admitting air on application or bypassing oil on application
you have to first check that it is hydraulic operation as the brake master cylinder may have fluid but that is a separate system to the clutch
check that it is not cable operation in which case it will be a broken cable
after the simple check , if it is a hydraulic system , replace both slave and master cylinder as they both wear out together and if it is cable replace the cable

Nov 11, 2016 | Ford Cars & Trucks

1 Answer

I have a 2003 ford escape that the clutch goes to the floor & doesnt return up. But there is no leaks at any points of the slave cylinder point up to the master cylinder??


slave cylinder/hydraulic throwout bearing or master cylinder can internally bypass... suspect master cylinder but always check all components before hanging parts because it could also be as bad as a damaged clutch assy...

Dec 30, 2013 | Ford Escape Cars & Trucks

1 Answer

Cant locate clutch cylinder 1988 Honda accord lx 5 speed trasmssion


If it is a hydraulic clutch, and not cable operated, there will be two cylinders. A clutch master cylinder will be mounted on the firewall next to the brake master cylinder. One steel line will go from the master cylinder down to the slave cylinder bolted onto the transmission housing where the clutch lever extends out of the housing. Other than bleeding the slave cylinder, no adjustments are necessary on hydraulic clutches. Cable operated clutches have an adjusting mechanism to take up slack when the clutch disc wears. The adjuster will be inside the engine bay.

Sep 22, 2013 | 1987 Honda Accord

1 Answer

How do i bleed the brakes on a 1999 Pontiac Grand Am?


Bleeding the Brake System
When any part of the hydraulic system has been disconnected for repair or
replacement, air may get into the lines and cause spongy pedal action (because
air can be compressed and brake fluid cannot). To correct this condition, it is
necessary to bleed the hydraulic system so to be sure all air is purged.

When bleeding the brake system, bleed one brake cylinder at a time, beginning
at the cylinder with the longest hydraulic line (farthest from the master
cylinder) first. ALWAYS Keep the master cylinder reservoir filled with brake
fluid during the bleeding operation. Never use brake fluid that has been drained
from the hydraulic system, no matter how clean it is.

The primary and secondary hydraulic brake systems are separate and are bled
independently. During the bleeding operation, do not allow the reservoir to run
dry. Keep the master cylinder reservoir filled with brake fluid.


  1. Clean all dirt from around the master cylinder fill cap, remove the cap and
    fill the master cylinder with brake fluid until the level is within 1/4 I n.
    (6mm) of the top edge of the reservoir.
  2. Clean the bleeder screws at all 4 wheels. The bleeder screws are located on
    the top of the brake calipers.
  3. Attach a length of rubber hose over the bleeder screw and place the other
    end of the hose in a glass jar, submerged in brake fluid.
  4. Starting at the right rear proceed in this order left front, left rear and
    right front.
  5. Open the bleeder screw 1/2 - 3/4 turn. Have an assistant slowly depress the
    brake pedal.
  6. Close the bleeder screw and tell your assistant to allow the brake pedal to
    return slowly. Continue this process to purge all air from the system.
  7. When bubbles cease to appear at the end of the bleeder hose, close the
    bleeder screw and remove the hose.
  8. Check the master cylinder fluid level and add fluid accordingly. Do this
    after bleeding each wheel.
  9. Fill the master cylinder reservoir to the proper level.


prev.gif next.gif

Sep 21, 2010 | 1999 Pontiac Grand Am GT

1 Answer

My clutch is sitting on my floor board


This is caused by a failed clutch slave or master hydraulic clutch release cylinder has, it is best if these are replaced as a pair. here are the parts u need.
BRUTE POWER / PERFECTION CLUTCH Part # 39836 Hydraulic Clutch Master cylinder
BRUTE POWER / PERFECTION CLUTCH Part # 3788 Hydraulic Clutch Slave Cylinder

Jul 30, 2010 | 1993 Honda Prelude

Not finding what you are looking for?
1996 Ford Taurus Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...