Question about 2001 Chevrolet Impala
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: fuel pump 2000 chevy blazer
Check your connections. did you run the fuel pump wiring under the drivers side door sash like GM did?.. if so check for nicks in the wire or bending or cracks.. this happens.. happened to me. check your fuel pressure. 40 dollar part at an auto store. If its below 59 PSI it wont work. And blazers are very intolerable to low fuel pressure. Also try taking the negative post off your battery for a little while and then putting it back on and if you can get it started again drive around (if its safe and running decent) for at least 30 minutes to get your car computer system acclimated to a new functioning part. Did you check the fuel filter?. rule of thumb when a pump goes change the filter its always the last thing people expect because we all jump to catastrophic engine failure at the first no start moment. lol.
Make sure that all your ducks are in get my drift.. Air oxygen fuel thats the mixture you need to check all those vital parts. before pulling your head off.
Posted on Aug 08, 2008
it's located inside the gas tank. tank must be removed to access it.lower tank,label & remove hoses unplug wires.turn locking ring between plastic pump & tank,remove pump.reverse to assemble.
Posted on Sep 23, 2009
Try to do the crank relearn:
Ensure that your battery is fully charged before attempting the relearn procedure. Do not leave any battery charger or jumper cables attached to the battery. Close the hood completely. Some applications require that the doors remain closed during the procedure.
1. Rotate the key to the start position to attempt to start the vehicle (the vehicle will not start).
Allow the key to return to the all position (same as if the vehicle would have started). The theft system light will flash (or stay lit) on the dash for approximately 10 minutes.
2. When the theft system telltale stops flashing (or turns oft) turn the key to the off position for 5 seconds and then attempt tostart the vehicle. The vehicle should start on this cycle.
3. Once the vehicle is running, the password relearn is complete.
00 + S10
1. Rotate the key to the start position to attempt to start the vehicle (the vehicle will not start). Allow the key to return to the on position. (same as if the vehicle would have started)
2. The theft system light will flash (or stay lit) on the dash for approximately 10 minutes.
3. When the theft system telltale stops flashing (or turns off) turn the key to the off position for 5 seconds and then attempt to start the vehicle.
4. Repeat steps 1 through 3 two more times for a total of 3 cycles/30 minutes.
5. On the next cycle of turning the ignition key from off to crank the vehicle should start
6. Once the vehicle is running, the password is learned and this completes the cycle.
7. Clear any DTC's with a scan tool if necessary. DTC history will be cleared after 100 ignition cycles.
Thank you for using fixya and keep me posted, be glad to help you get your jimmy running 100%
Posted on Apr 26, 2010
Tips for a great answer:
Apr 05, 2017 | Cars & Trucks
Dec 12, 2016 | 2003 Chevrolet Impala
Aug 29, 2014 | 2001 Chevrolet Impala
Apr 13, 2014 | 2001 Chevrolet Impala
Feb 21, 2012 | 2001 Chevrolet Impala
Dec 11, 2011 | 2002 Chevrolet Impala
Jul 12, 2011 | 2001 Chevrolet Tracker
Sep 02, 2010 | 2001 Chevrolet Impala
Mar 31, 2009 | 2001 Chevrolet Impala
30 people viewed this question
Usually answered in minutes!