Question about Cars & Trucks

1 Answer

Trying to put piston in a 1990 kx250 but cant remeber which way the Aarow goes

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 46,758 Answers

Normally to the front of the engine if it is in line with the gudgeon pin

Posted on Jan 12, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 ford ranger i removed the wires off the stsrter silsnoad a year now i cant remeber how to put them back


The heavy cable goes to the big nut and the push on wire goes to the spade or push on terminal.

Oct 02, 2016 | 1992 Ford Ranger

1 Answer

I have a 1990 buick lesabre and i cant get one o the break pads on....... what am i doing wrong?


you may not have the caliper pistons fully compressed so the brake pads will not go back on. Place a large C-clamp over the left inboard caliper housing and the outboard pad, and tighten to compress the caliper piston. good-day !!

Jul 29, 2011 | 1990 Buick LeSabre

2 Answers

1990 318i engine no compression yet timing chain ok cam and lifters working pistons going up and down has spark 0 compression wont start


I suggest you bring the pistons to TDC, one at time on the comprssion stroke and do a "cylinder leakage test". Put compressed air into the spark plug hose and try to detect where the air is going. If you have the piston exactly at TDC, it will stay there when you put conpressed air in the hole, if it's off a little it will push the piston down. If you have the valve cover off you can watch the valves to determine if you have the pistons on the compression stroke. You should be able to buy a fitting from an auto parts store that will thread into the spark plug hole. If not take an old spark plug and bust the guts out of it and weld a pipe fitting to it to adapt your air compressor hose.

Mar 07, 2010 | 1996 BMW 318

1 Answer

Brake piston will not go in on a 1990 buick regal


Try opening that calipers bleeder valve first.Close when piston is fully in. Piston might also be cocked. That is , tilted. push piston on high side. then proceed squarely.

Dec 07, 2009 | 1990 Buick Regal

2 Answers

How to compress rear caliper piston on 1990 volvo 240 dl


use c type clamps compress slowly clean caliper first

Sep 20, 2009 | 1990 Volvo 240

3 Answers

1990 chevy brakes


Use a C clamp and squeeze the caliper piston back in. Put the pads in place and try it. That should do it. Remember to push on the pedal a few times before you drive it. Check the fluid before you drive it.

Jul 03, 2009 | 1990 Chevrolet K1500

1 Answer

Cant find where to put transmission fluid under the hood


transmission fluid goes through the channel where you check the fluid. you need a funnel to put oil in cressidas transmission.

Mar 24, 2009 | 1990 Toyota Cressida

2 Answers

Brake pistons won't retrack to allow new brake pads to be install


It's possible the pistons "screw" back in, even though they don't look like they are threaded. Very much like X-1/9 calipers. You might also attach a small hose to the bleed valve, and squeeze the pistons with a large set of pliers.

Dec 24, 2008 | 1988 Toyota MR2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...