Question about 2007 Pontiac Solstice Convertible

Open Question

How to remove front floor console 2007 solstice

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 buick lacrosse console gear indicator bulb


Transmission Floor Shift Control Indicator Lamp Replacement

Remove the front floor console. Refer to Front Floor Console Replacement.
Rotate the floor shift control indicator lamp socket (2). Pull the socket from the trim bezel.
Remove the bulb from the socket.

Front Floor Console Replacement

Preliminary Procedures
Remove the rear floor console. Refer to Rear Floor Console Replacement.
Remove the instrument panel lower trim plate. Refer to Instrument Panel Lower Trim Plate Replacement.
Set the parking brake, then shift the transmission into drive and push the shift indicator down until it locks, to allow clearance to remove the console.
1
Front Floor Console Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Front Floor Console Bolt (Qty: 2)
Tighten
10 N·m (88 lb in)
3
Front Floor Console Assembly
4
Front Floor Console Retainer Clip (Qty: 2)

Feb 24, 2017 | 2009 Buick LaCrosse

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

Center console removal


Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.



showgif.do?image=1875475





tif.gif








Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure




  1. Disconnect the electrical connectors.


  2. When replacing the front floor console accessory housing assembly, transfer all necessary components





  1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .


  2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .



1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures


  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .



1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)





showgif.do?image=1858392





tif.gif








Callout







Component Name






Preliminary Procedures




  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .


  3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .







1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure



  1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.


  2. Disconnect the electrical connectors.


  3. With the aid of an assistant remove the console assembly from the vehicle.


  4. When replacing the front floor console, transfer all necessary components.





h4hqqpweof7+aaaaaelftksuqmcc

arzs+0tf0j6faaaaaelftksuqmcc

Jan 10, 2015 | 2008 Buick Enclave

1 Answer

How to install a center console on a pacifica


Hi Melissa, I'm glad to help, here is the instruction below I said I'd send. Have an awesome day.


23 - Body/Interior/CONSOLE, Floor, Front/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure 1. Remove shift bezel. (Refer to 23 - Body/Interior/BEZEL, Shifter - Removal) .
2. Remove transmission range indicator surround bezel Figure 1.
3. Remove two screws attaching front floor console to the lower instrument panel Figure 2. 4. Open cup holder and remove two attaching screws to bottom of cup holder. 5. Open bin and remove two attaching screws to bottom of bin. 6. Remove front floor console sidewall attaching screws, three per side. 7. Raise front floor console and disconnect wiring harness. 8. Remove front floor console from vehicle.
374297.jpg Figure 1 - TRANSMISSION RANGE INDICATOR SURROUND BEZEL 1 - INSTRUMENT PANEL 2 - AUTOSTICK SHIFTER ASSEMBLY 3 - TRACTION CONTROL SWITCH 4 - TRANSMISSION RANGE INDICTOR SURROUND BEZEL 5 - KNOB SET SCREW 6 - SHIFTER KNOB 7 - FLOOR SHIFT BEZEL 8 - WIRE CONNECTOR 9 - INSTRUMENT PANEL WIRING HARNESS 10 - INSTRUMENT PANEL WIRING CLIP
374299.jpg Figure 2 - FRONT FLOOR CONSOLE 1 - FORWARD CONSOLE CLOSEOUT PANEL 2 - CLOSEOUT PANEL PUSH PIN RETAINER 3 - INSTRUMENT PANEL WIRING 4 - FLOOR CONSOLE BASE 5 - FRONT FLOOR CONSOLE ATTACHING SCREWS TO LOWER INSTRUMENT PANE AND BASE 6 - FRONT FLOOR CONSOLE WIRING CONNECTOR 7 - FRONT FLOOR CONSOLE 8 - ATTACHING L-BRACKETS

May 17, 2014 | 2006 Chrysler Pacifica

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

How i can replace the gearshift?


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console -Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Feb 13, 2011 | 2003 Lincoln Navigator

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

Right front tire has gone flat 3 times in the last


You can remove the tire from the vehicle, make sure it is properly inflated, and spray with a soap and water solution. Carefully look around the bead, check the tread for bubbles, could be a puncture, and don't forget to look at the valve stem. Any bubbles indicates a leak. Good luck.
Steve

Jan 02, 2010 | 2007 Pontiac Solstice Convertible

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

1 Answer

How can i find out my parking brake adjustments on my 2003 ford escape?


Parking Brake Cable Adjustment Vehicle with low series floor console
  1. Remove the floor console front finish panel.
    1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
    1. Remove the floor console front finish panel.
  1. Remove the floor console rear finish panel.
    1. Apply the parking brake.
    1. Remove the floor console rear finish panel.
Vehicle with high series floor console
  1. Remove the floor console finish panel.
    1. Apply the parking brake.
    1. Remove the floor console finish panel.
All vehicles
  1. Remove the adjustment nut clip.
  1. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.
  1. Confirm the parking brake is applied.
  1. Install the adjustment nut clip.
Vehicle with high series floor console
  1. Install the floor console rear finish panel.
Vehicle with low series floor console
  1. Install the floor console rear finish panel.
  1. Install the floor console front finish panel.
    • If equipped, install the manual transmission shifter knob by turning clockwise.

Jan 21, 2009 | 2003 Ford Escape

Not finding what you are looking for?
2007 Pontiac Solstice Convertible Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...