Question about 2000 Acura TL

1 Answer

Print out to change front hub &bearing - 2000 Acura TL

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 74 Answers

Front or rear? They are not the same

Posted on Jan 12, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

2 Answers

Replaceing front hub bearings on '05 GMC sierra 4X4


Remove the caliper & rotor,axle nut & unbolt
the axle hub bearing assy

Watch some video on it

You do both sides at the same time

Aug 14, 2014 | Cars & Trucks

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

Is there any special tools required to change front wheel bearing on 2003 mini


you will need a big socket to remove the axle nut--about 20 mm or so. Other than that, I don't think so. Procedures from autozone.com below. it doesn't mention having to press bearing into hub.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheels Hub nut Brake caliper Rotor ABS sensor Wheel hub from steering knuckle and driveshaft Wheel bearings
To install:
  1. Install or connect the following:

    Wheel bearing into hub Wheel hub to steering knuckle and driveshaft; torque bolts to 41 ft. lbs. (56 Nm) ABS sensor; torque to 6 ft. lbs. (8 Nm) Brake rotor and caliper New flanged hub nut; torque to 134 ft. lbs. (182 Nm)

Oct 05, 2010 | 2003 Mini Cooper

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

How do I change front hub and bearing assembly on 2004 Explorer


Front hub bearing, remove tire, remove caliper and caliper holding bracket, you do not have to remove brake caliper from brake hose, just set it aside, if 4X4 remove front axle nut that goes through center of rotor, also remove brake rotor, disconnect elec, A.B.S connector, remove three bolts on back side of hub bearing, remove hub bearing, some times you will need to knock hub bearing out with a hammer.Reverse to install new hub bearing.

Jul 09, 2010 | 2004 Ford Explorer

1 Answer

Front hub bearing changed now traction keeps coming on.


It seems that either the bearing is not properly fitted leading to false alarm being generated(maybe the bearings are too tight) such that the brake pads are not equidistant compared to the other side wheel. Well the thumb rule is to replace both since they are the front wheels. Try refitting the bearing but my instinct tells me to change the other wheels bearing too and get the brakes reset with the help of computer guided sensor settings checking & adjustments as required. This will definitely help but don't forget to recalibrate the sensors with the help of a PC at the service station. Its IMP......sodeep

Jul 30, 2009 | 2005 Hummer H2

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

3 Answers

How to change front wheel bearing ford focus


You can do it yourself just take your time:
To change front wheel bearing.
1. Jack car up support with jack stands
2. take tire off
3. take caliper and brakes off
4. take rotor off
5. unbolt axle shaft nut at bearing hub
6. use a 3 lb slug with a block of wood
7. place wood on axle shaft and knock it in
8. back side 3 10mm bolts unbolt
9. front side have to pry off bearing hub Assembly only beacuse has dirt in knuckle hole.
10. clean hub knuckle and reinstall.
Its really not that hard or you could have them done for $900 and up. (I have changed alot of wheel bearing assemblies )Whats your e-mail I can send you a diagram if you want.

May 01, 2009 | 2004 Ford Focus

2 Answers

Noisy front wheel bearing


It is possible but i do reccomend changing the bearing races in the hub when you do it to prevent any premature wear on your new bearings. A new hub/rotor assembly will come with new races installed if that makes it any easier.

    130890.gif
    tif.gif
moz-screenshot.jpgmoz-screenshot-1.jpg

Dec 12, 2008 | 1998 Chevrolet C1500

Not finding what you are looking for?
2000 Acura TL Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...