Question about 1983 Chevrolet Camaro

Open Question

Instructions to replace 83 camaro ignition key switch

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cartersintn
  • 62 Answers

SOURCE: Ignition switch

1) remove horn pad
2)looosen steering wheel nut
3) use steering wheel puller to remove steering wheel
4) use lock plate compression tool to push down lock plate and pry c-clip up onto lock compression tool unsrew and remove tool
5) lift compression plate out of way
6) remove turn signal acuator, then remove three screws that retain the turn signal harness
7)you will see white piece of platic to the right that is you buzzer button reomove it pull straight out
8) unscrew phillips screw that holds in ignition and pull ignition out. Hope this helps you

Posted on Sep 10, 2008

GM Elec
  • 1000 Answers

SOURCE: Help locating the Ignition Switch on a 2001 Camaro PLEASE!

It should be located on the right side of the steering column about half way to the floor. It is activated by a rod connected to the lock key cylinder that runs down the column to the switch.
Let me know if you need anything further.
Good luck.
Regards,
327dcf1.gif

Posted on Feb 21, 2009

  • 262 Answers

SOURCE: replace ignition in 1999 camaro

The steering wheel does have to come off to access the ignition lock cylinder, however the ignition switch is mounted to the column and does not require the wheel to be removed. A locksmith would have rekeyed the lock cylinder. The high beam switch is mounted of the left side of the column and is actuated by a 6 inch long rod. This does not require the wheel to come off.

Posted on Feb 24, 2010

Testimonial: "Thank you very much for the info. I appreciate it very much. JT"

  • 2002 Answers

SOURCE: 83 camaro has no lights at all. all fuses are good

Check the fusible links on the starter harness. There should be 2 black rubber plugs on the wires going to the starter. I'm not sure which one is for the lights. I always replaced both because I figured if one was bad it wouldn't be long before I'd be back under there to do the other one. Hope this helps.

Posted on Jun 13, 2010

  • 1857 Answers

SOURCE: Need written instruction on installing an Ignition

go to mitchell1diy online and pay the ten bucks if noone responds..

Posted on Jul 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 2.8 camaro starts an dies, but will run on spray. new computer, dist. injectors an pump.


Hold the ignition switch just off where the engine cranks after it starts, if it stays running you need to replace the ignition starter switch. This is the switch at the bottom of the steering column that the key cylinder operates via a rod. See photo below.
26380888-ycldav1j2xqu0dfv4h5tom5t-2-0.jpg

Dec 01, 2016 | 1986 Chevrolet Camaro

1 Answer

83 camaro wont start, got new ignition switch and tumbler.


It's probably time to pull the starter off and have it tested. I think places like autozone or advance will check it free. Before you do that, make sure all connections are clean and tight.

Aug 02, 2015 | 1983 Chevrolet Camaro

1 Answer

Chevy camaro ignition I changed the relay


sound like ignition switch and keylock cylinder broken.

Oct 06, 2013 | Cars & Trucks

1 Answer

I need to replace the ignition switch on my 94 Camaro. Do I have to use a special ignition switch that uses the "VATS" system, or can I just replace the switch that comes with its own set of keys that are...


you can use any non-VATS lock/key and then get rid of the VATS system completely with this: http://newrockies.com . It will save you a lot instead of buying the VATS key/lock to match your TDM.

Aug 17, 2010 | 1994 Chevrolet Camaro

1 Answer

Replace ignition in 1999 camaro


The steering wheel does have to come off to access the ignition lock cylinder, however the ignition switch is mounted to the column and does not require the wheel to be removed. A locksmith would have rekeyed the lock cylinder. The high beam switch is mounted of the left side of the column and is actuated by a 6 inch long rod. This does not require the wheel to come off.

Feb 24, 2010 | 1999 Chevrolet Camaro

2 Answers

95 chevy camaro with pass key will not start. Replaced key and it started. Later it did not start. What's going on? What are some things to try?


If it's the same as the VATS system in my 86 Corvette (resistor pellet in key) the ignition switch might need to be replaced. The contacts on the key wore low, replacing the key helped for a short time but the new contacts wore the switch down faster then it too needed to be replaced. $200!

Nov 16, 2009 | 1995 Chevrolet Camaro

1 Answer

How do i reprogram my ignition switch n my 92 camaro rs.i will not start ,brand new starter,ignition switch. new fuses.all the power comes on.


You can't. I just replaced mine on my 92 Camaro and it's a pain in the ***. You can only install the ignition switch one way, then you have to make sure that the rod coming off the tumbler (where your key goes) is in the right spot.

Nov 14, 2009 | 1989 Chevrolet Camaro

2 Answers

Key Stuck In Ignition, 1995 Chevrolet Camaro


well you kn ow the b*tch likes to **** no seriously though try moving the stearing wheel left and right

Jun 02, 2009 | 1995 Chevrolet Camaro

1 Answer

Help locating the Ignition Switch on a 2001 Camaro PLEASE!


It should be located on the right side of the steering column about half way to the floor. It is activated by a rod connected to the lock key cylinder that runs down the column to the switch.
Let me know if you need anything further.
Good luck.
Regards,
327dcf1.gif

Feb 21, 2009 | 2001 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...