Question about 2003 Ford Expedition

1 Answer

2003 Ford Expedition XLT FX4 MAIN FAN CONTROL SWITCH

The fan control switch only works on the high speed. It does not work on the other speeds. All of the directional ariflow works as I can switch form defrost to feet to combo....The rear vents and fan controls do work at all speeds. The main only works on the HIGH speed.

Posted by on

  • clevelandcon Jan 28, 2009

    I have the exact same problem on the same year expedition. If it is the board on the fan motoer, can you tell me how to find it?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

That usually means the circuit board for the fan motor is Burt out big job prob to replace dealer may be.

Posted on Jan 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford explorer sport trac blower motor and switch not getting any power, it was working fine a while ago and i had to start flipping the switch to head then off then back to head, what is wrong?


The selector switch on the dash controls the blower motor relay, then the fan switch controls the speed. The fan switch gets power from a 40amp fuse and the control panel gets power from two other fuses.
If you are working the control switch to get the fan to work, the control switch may be failing.

May 28, 2013 | 2003 Ford Explorer Sport Trac

1 Answer

2003 ford escape fans do not run in till the a/c is turned on.


There are four relays for the cooling fans .low speed control , medium speed , high speed fan control relay 2 , high speed fan control relay 1, there is also a engine cooling fan resistor .The engine coolant temp. sensor would most likely cause the check engine light to be on . There is also a dual pressure switch , this is for the A/C . The cooling fans will be turned on at 213 degress low speed , high speed at 226 degress . If you had factory scan tool or a professional type you could view coolant temp data in pcm , you could also energize the relays to see if the system is operating normally . There are other repair shops beside dealers

Mar 28, 2017 | 2003 Ford Escape

1 Answer

I have a 2004 Pacifica and the blower motor runs on high all the time, can't get it to work on slower speeds


The high blower works off a relay in the high speed only so the fan switch is at fault on your vehicle
Replace the fan blower control speed switch which is the one you adjust the lower fan speeds

Jun 15, 2010 | 2004 Chrysler Pacifica

2 Answers

Need wiring diagram for fan speed switch on 2003 gmc sierra


the fan control balast (or speed controler) is burned out. by design if it only goes high, its junk. replace it and youll have it fixed. should be by the fan under the dash on the passenger side.

Nov 15, 2009 | 2003 GMC Sierra

1 Answer

Front ac blower fan only works on only


many vechicles have a relay that when defective does not allow low speed operation, (it usually controls the lo speed) check in the relay and fuse box, there may be two boxes one not as obvious

Oct 09, 2009 | 2003 Ford Expedition

3 Answers

First 2 speeds of the fan wont work for heater


sounds like the switch and is fairly easy to remove and replace the switch ..

Sep 07, 2009 | 1999 Ford Expedition

2 Answers

My blower motor fan speed switch will work only on High.


I had a similar problem with my 03 Taurus. Does your floorboard on the passenger side get wet when it rains really hard? If so, Ford is aware of a defect above the fan motor which is behind the glovebox.
I contacted Ford directly and they had my local ford dealer fix it free and they gave me money towards a new blower motor which shorted out from the leak, it's possible it just your switch if there is no leak but you might need both the switch and blower motor replaced like I did. Hope this helps.

Apr 10, 2009 | 2003 Ford Taurus

3 Answers

Heat/AC Blower fan speed only works on High


Alot of people have the same problem with the fan switch and blown bulbs. There really is no fix for this. Jeep really screwed up when designing the heater control assembly. The cheapest solution is to buy another unit off Ebay. Can always go to the dealer but be ready to PAY for there mistakes.

Jan 14, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Ford Expedition Logo

Related Topics:

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...