Question about Cars & Trucks

1 Answer

My 2002 Volkswagen golf 2.0 shifter got really loose can't tell what gear im in. When I put it into first I can get it to role with allot of gas but still doesn't feel like it's in gear and when I stop and get off the clutch it stalls out.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 74 Answers

The transmission in a Volkswagen vehicle shifts gears only when there is enough hydraulic pressure. This is made possible in part by the clutch cable, because it connects the clutch pedal to the clutch master cylinder. The clutch master cylinder in turn transforms the foot pressure that is carried through the clutch cable into hydraulic pressure. If the clutch cable breaks, the clutch master cylinder will be unable to generate enough hydraulic pressure for shifting gears.

Posted on Jan 12, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: manual transmission shifter will not engage

Sounds to me that the shifter broke, i believe the shifter has a ball end that slips into a pocket in trans. that moves for gear selection and that ball brook off end of shifter. if its got a linkage set up most likely samething either shifting arms came off or shifter broke where linkage rods connect.

Posted on Feb 12, 2009

  • 231 Answers

SOURCE: hard to change gear

sounds like your slave cylinder for your clutch is by-passing.

Posted on Oct 18, 2008

urnuts73
  • 210 Answers

SOURCE: cannot put gear shifter on column into park,

sounds like the shift linkage has fell off
look under the hood of your car and have someone move the shifter
look for the movement and see is it is hooked up
give me feed back if this helps

Posted on Jan 23, 2011

Testimonial: "good help. this exactly what my 2000 taurus is doing too. and the answer is sounds like it is the key to my problem. taurus is a darn good car!!!!!"

  • 4369 Answers

SOURCE: just put in new clutch

what you mean is the clutch is not disengaging the transmission from the engine, so you can shift it.

This is always due to air trapeed in the clutch system. It is very hard to purge the air.

You may have to have a shop use their evac/fill equipment, if they have it.

Try raising the front of the truck as high as you can, including facing uphill. The air is likely trapped at the slave cylinder, not at the clutch.

There is a video on you tube showing a guy purging air from a Ranger. See if you can view it.

1) The Hydraulic system should be bled to remove all the air whenever air enters the system. This occurs if the fluid level has been allowed to fall so low that air has been drawn into the clutch master cylinder. Under normal circumstances, air should not enter the system when the quick disconnect hydraulic line fittings have been disconnected. The procedure is very similar to bleeding a brake system, but depends mainly on gravity, rather than the pumping action of the pedal, for the bleeding effect.

2) Fill the master cylinder to the top with new brake fluid conforming to DOT 3 or DOT 4 specifications. Caution: Do not re-use any of the fluid coming from the system during the bleeding operation and don't use fluid from which has been inside an open container for an extended period of time.

3) Raise the vehicle and place it securely on jack stands or drive it securely up on ramps (whichever method you chose) to gain access to the bleeder valve, which is located on the top left side of the bellhousing (See Illustration 1-1 below). Try to keep the truck as level as possible. Caution: Don't forget to chock the rear wheels and set parking brake for extra safety...

4) Remove the dust cap which fits over the bleeder valve and push a length of clear plastic hose over the valve. Place the other end of the hose into a clear container.

5) Open the bleeder valve. Fluid will run from the clutch master cylinder, down the hydraulic line, into the release cylinder (the Slave Cylinder) and out through the clear plastic tube. Let the fluid run out until it is free of bubbles.
Note: Don't let the fluid level drop too low in the clutch master cylinder, or air will be drawn into the hydraulic line and the whole process will have to be started over.

6) Close the bleeder valve.

7) Open the bleeder valve and have an assistant slowly depress the clutch pedal allowing fluid to flow through the clear plastic hose. When the clutch pedal is almost to the floor, close the bleeder valve and have the assistant release the pedal.

8) Slowly press the pedal five times, waiting two (2) seconds each time the pedal is released. When releasing the pedal on this step, release it fast. This tends to help **** fluid down the stream and aid in faster bubble reduction.

9) Fill the fluid reservoir to the top.

10) The clutch should now be completely bled. If it isn't, (indicated by failure to disengage completely, and a soft or no pedal), repeat steps 5 through 9.

11) Continue this process until all air is evacuated from the system, indicated by a solid stream of fluid being ejected from the bleeder valve each time with no air bubbles in the hose or container.

12) Install the dust cap and lower the vehicle. Check carefully for proper operation before placing vehicle in normal service. Check the fluid level.

Note: If you can NOT get fluid out of the bleeder screw, then the internal check valve in your clutch master cylinder may be stuck, or you haven't bleed the system for at least 30 minutes. You will either have to use a different bleed technique, or replace the clutch master cylinder. Bleeding a Ranger clutch system takes time and patience. One small mistake / loss of patience / or shortcut, and you'll have to start all over.

Posted on May 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do i have to do to fix the fact that the automatic transmission in a 2002 volkswagen golf gti is stuck in neutral, but will move freely to park and drive.


Likely shift linkage or cable have come loose or broken. Put car on rack, have assistant sit in car and work shifter while you watch from underneath. If all appears normal, remove trans pan to see linkage inside.

Mar 21, 2016 | Volkswagen Cars & Trucks

1 Answer

My 2007 Volkswagen Jetta is stuck on parking gear


VW Jetta neutral override trick - YouTube

? 1:31
https://www.youtube.com/watch?v=GFw2j6ufTH8
May 28, 2013 - Uploaded by Pop Acap
This 2005 VW Jetta SE was involved in a motor Vehicle Accident and ... I had troubles with my vauxhall zafira 1 ...

STUCK IN PARK!!! - Volkswagen Forum - VW Forums for Volkwagen ...

volkswagenforum.com > ... > VW MODELS > Volkswagen Jetta/Bora
Aug 10, 2006 - i was driving into my apartment complex, and i put my car in park ... He checked the shift lock, fuses, brake light switch, computer stuff ... Automatic ShifterStuck in Park, waldo358, Volkswagen Passat, 1, 12-27-2007 05:23 PM.

Automatic stuck in Park - doesnt seem to be brake switch - TDIClub ...

https://forums.tdiclub.com/showthread.php?t=323777
Jul 12, 2011 - Automatic stuck in Park - doesnt seem to be brake switch VW ... TDI(s): 2002 VW Jetta TDI Manual(performed 01M to 5-speed swap) .... Bad Brake light switch - stuck in park, Joe Golf, TDI 101, 2, November 25th, 2007 17:48. Audi A6 Stuck In Park - Read More
Oct 17, 2015
PRNDS Lights Flashing, Stuck in First Gear
Dec 31, 2013
Help Plz! Jetta Shifter Wont Shift from Park!
Dec 17, 2010
More results from forums.tdiclub.com

Dec 30, 2015 | Volkswagen Cars & Trucks

1 Answer

Isaac


Check the linkage first . A pin may have fallen out of a pivot point and the linkage has fallen off.

May 19, 2013 | Volkswagen Cars & Trucks

1 Answer

Golf 4 'Comfortline' front passenger electric window


It needs a window regulator repair kit . Not really a home diy fix . Unless you have some experience . Regards

Jan 17, 2009 | 2002 Volkswagen Golf

1 Answer

I have a 95 Golf with a loose back wheel


dont drive! remove the rear hub and check and replace bearings. hopefully it didnt do any further damage

Sep 14, 2008 | 2002 Volkswagen Golf

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...