Question about 2003 Ford Crown Victoria

Open Question

Heater problem with a 2003 ford crown victoria

My aircondition blows out cold air, but the heater won't work, it just blows out cold air too.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: 2006 crown victoria - no heat

I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Posted on Jun 21, 2008

Ad
alicantecoli
  • 22156 Answers

SOURCE: Ford Expedition 2002 Front Heater blows cold air below 45 MPH

impeller is made of plastic on teh water pump and its slipping and spinning on the shaft renew before weather warms up as engine will overheat

Posted on Jan 01, 2009

jamaicanmech
  • 17 Answers

SOURCE: My 1999 Ford F150 Heater only blows out cold air

guys have you checked for a vaccum leak????? there is a little plastic ball with a vaccum line going to it that controls the outside air coming in. check for a leak in this line

Posted on Jan 08, 2009

  • 104 Answers

SOURCE: 2003 Ford Crown Victoria misfires when

I HAVE HAD THE SAME PROBLEM ON SEVERAL CROWN VICS I HAVE WORKED ON ,& SOME OF THEM A SET OF PLUGS STOPPED IT,AND SOME OF THEM HAD TO HAVE 1 OR MORE COIL PACKS REPLACED, BUT THE PROBLEM THAT I FOUND THAT IF PLUGS & ALL COIL PACKS HAD BEEN REPLACED,AND IT WAS STILL IN THE IGNITION, IS THE WIRES GOING INTO THE PLUG ON THE COILPACK UNDER THE INTAKE TUBE, IF YOU REMOVE THE INTAKE TUBE,LOOK CLOSE AT THE WIRES FOR ANY BARE SPOTS,& LOOK AT THE BOTTOM OF THE INTAKR TUBE IF YOU CAN SEE WHERE IT HAS RUBBED IT,IT IS ALMOST A GIVEN THERE IS A BARE SPOT OR CRACKED INSOLATION ON THE WIRE, ENOUGH TO CAUSE A MISFIRE, (FYI) IT TOOK ME MANY TIMES OF INSPECTING BEFORE I LOOKED CLOSE ENOUGH TO SEE THE BARE SPOTS, BUT ALL YOU HAVE TO DO IS STRIP THE HARD PLASTIC AROUND THE WIRES BACK ENOUGH TILL YOU SEE GOOD CLEAN LOOKING WIRE,THEN SEPERATE THE WIRES AND IF YOU HAVE LIQUID ELECTICAL TAPE USE THAT AND THEN TAPE THEM WITH ROLL ELECTRICAL TAPE ,BUT IF YOU TAPE THEM UP GOOD SO WHEN THE WIRE IS BENT ENOUGH FOR THE INTAKE TUBE TO CLEAR ,& YOU CANNOT SEE THE WIRES GOING IN TO THE PLUG WITH A ROLL OF ELECTRICAL TAPE THAT WILL WORK TOO, I HOPE THIS TRICK WILL WORK AS GOOD FOR YOU AS HAS ME ON DOZENS OF CROWN VICS, ESPECIALLY P71 POLICE CARS.

Posted on Dec 05, 2009

  • 185 Answers

SOURCE: 2003 Ford explorer heater blowes out cold air

Check your anitfreeze level,.

and your thermostat if the level is OK.

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No hot air working with heat on only cold air blowing in my ford crown victoria


CHECK THE RADIATOR WATER. SOMETIME IT CAN ALSO MAKE A DIFFERENCE

Oct 14, 2012 | 2001 Ford Crown Victoria

1 Answer

My heat works but it is blowing any air


have your blend motor checked and you blend door

Nov 08, 2011 | 1996 Ford Crown Victoria

2 Answers

2006 crown Victoria blows hot air with the air conditioner on the air condition lines are cold under the hood


sounds like the temperature blend door is either jammed or the actuator is shorted ou. when the temperasture control is moved you should hear the door moving...my guess is you are not hearing that..the actuator would be attached to the heater plenum behind dash/glovebox area...becareful to test the correct one as there will be a fresh air actuator and a mode door actuator as well...you can determine which one is which by changing the positions on heater head from hot/col, floor/defrost, recirculate and fresh air settings..each setting will move its designated actuatror..the one not moving would be you temp actuator....have fun!

Jun 29, 2011 | 2006 Ford Crown Victoria

1 Answer

Heater blows cold air


ok so the heater draws heat from the engine and if the engine dose not heat up anuff it will only blow cold air the reason the engine may not be getting worm is because the thermostat may be stuck open

Jan 27, 2011 | 1995 Ford Crown Victoria

1 Answer

Heat goes on and turns to cold air 96 crown victoria. fixed waterpump, changed termostat, heatercore blown out twice, fluids are good. car sometimes acts like it has stored up heat, hot air will blow out...


did you buy the heater cores new heater core and radiator is two different things sounds like you thermostat is bad touch your bottom hose and your top are they both hot if ones hot and ones cold water is not circulating bad thermostat is the heater core put in right

Dec 03, 2010 | 1996 Ford Crown Victoria

1 Answer

Blows cold air out of heater ,thermostat is new


try venting the top heater hose of air,just undo the jubilee clip to expel all the trapped air.....

Oct 28, 2010 | 2006 Ford Crown Victoria

1 Answer

Heater blows cold air but sometimes will blow


Change thermostat if that doesn't solve the problem then its probaly a bad heater core

Jan 04, 2010 | 1994 Ford Crown Victoria

1 Answer

2006 crown victoria - no heat


I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Jun 20, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...