Question about 1987 Ford Ranger

Open Question

1987 ford ranger speed sensor location - 1987 Ford Ranger

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

emissionwiz
  • 75005 Answers

SOURCE: speed sensor diagram for 2000 ford ranger

It is in the hole (held in place by a Y shaped clamp) where the speedo cable used to go on the side of the trans, has 2 wires coming out of it, it is round with a round connector. Is this for an ABS problem? if so the sensor is on the top of the differential housing.

Posted on Nov 06, 2008

Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 1987 Ford Ranger 2.9 V6 4WD have a camshaft sensor? If so, approximately where is it located?


If you want to word it that way, it's inside the distributor. It's also called a pip sensor. It sends a signal to tfi module.
1987-ford-ranger-2-9-v6-4wd-camshaft-xwfqogg1klpxfycm0ntvtnbe-4-0.jpg

Nov 14, 2016 | 1987 Ford Ranger

1 Answer

Does the 1987 Ford Ranger 2.9 V6 4WD have a crank shaft position (CKP) sensor?


The ignition system engine controller uses a distributor sensor with a sector wheel to provide the ignition timing. This distributor pick up coil provides the (CKP) sensor function.


26354729-1xgjsougzksfoatycggrr2j0-2-0.jpg Hope this helps?

Nov 14, 2016 | 1987 Ford Ranger

1 Answer

Does a 1987 Ford Ranger 2.9 V6 truck have a crank sensor? If so, where is it located?


No it just has a distributor pickup coil, that in a sense is the crank sensor. These were a part that failed often.

Sep 12, 2016 | 1987 Ford Ranger

1 Answer

No power to fuel pump when key is on 1987 ford ranger


ck the inertia switch located on the foot wal under the carpet

Sep 11, 2014 | 1987 Ford Ranger

1 Answer

1987 ford ranger 2.9 v6 bacfires during decelaration


there Should be a Knock sensor located on the engine the other common fault for this problem is Leaking injectors or Carb hope this helps

Apr 20, 2011 | 1987 Ford Ranger

1 Answer

Speed sensor on a 1992 ford ranger. Where is it located.


The speed sensors are usually on the rear of the tranny, you should have 2 sitting back there, one is the speedometer, and the other is the speed sensor. Now, I am not 100% positive of your truck, but take a peek and see what you got. Hope it helps.

Sep 30, 2010 | 1992 Ford Ranger

2 Answers

Where is the oil pressure switch located on a 1987 ford ranger with a 2.9 L engine


2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block.

Jul 02, 2010 | 1987 Ford Ranger

1 Answer

Wear is the speed sensor on a 1990 ford ranger


The speed sensor is located on the end of the speedometer cable at the transmission tailshaft

Mar 31, 2010 | 1990 Ford Ranger SuperCab

1 Answer

1987 ranger


check the crankshaft sensor

Jan 19, 2009 | 1987 Ford Ranger

2 Answers

Speed sensor diagram for 2000 ford ranger


This video shows the speed sensor and its location for a 2000 ford ranger xlt. It also describes the problems a bad sensor can give.

Nov 06, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...