Question about 2005 Chevrolet Tahoe

1 Answer

2005 tahoe door ajar malfunction

Door ajar warning comes out on cluster when door is completely shut. What can be causing this? It only started doing this when it started to get cold(32 degrees and below).

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 74 Answers

Does the dash say what door? if so try taking the door panel off and lubing the latch assembly and check for connection problems

Posted on Jan 12, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: 99 Tahoe Front A/C blows warm rear A/C ice cold whats the problem

Would first establish if communal evaporator (cooling coils), hence possible blend door solution...
...or separate evaporator for front and rear as is found on some vehicles (if so then could have a plugged evaporator jet/orifice [the name escapes me at the moment])

Posted on Aug 09, 2009

manuelleiva
  • 97 Answers

SOURCE: Right rear door ajar warning stays on when door is

check the rear door pin switch and make sure its working properly.push it in and out and look at the dash at the same time to see if the warning light goes off.hope this info helps.take care and good luck, manny

Posted on Feb 08, 2010

  • 15 Answers

SOURCE: THE DOOR HANDLE ON MY 2007 CHEVY TAHOE IS COMING

On the O7 Model, that's a common stock issue. Interior problems with them are more common. Something to do with the way they were originally attached. Handles can come off very easy. The dealers will tell you they have to order "a whole panel piece" that includes the handle. For the Exterior Handle, I would try opening up the panel yourself to inspect the unit to see if something was broken inside or if maybe it just needs tightening. If it's the Interior Handle, sometimes you just need a mount clip replaced because it comes as a panel piece, all inclusive.

If it's the exterior handle and you are out of warranty, it gets a bit pricey so I would check online for replacements if you have a damaged one. For an amateur repair person, it can take a while. Check www.autopartswarehouse.com

For the Interior, another common problem is that the "Silver" Film on the handle comes off easily on some and begins to create "paper-like" cuts on your fingers. Check the clips on the mount panel and if necessary replace the unit. You might be able to just get the clips for Under $10.

The replacements can be much better with No sharp mold flash on them.

P/Ns are 15935951 & 15935954. Check to see which one applies to yours.
That one applies to the 07 with heated seats, which I'm assuming you probably have.

Hope that helps. Good Luck.

Posted on Apr 02, 2010

  • 1 Answer

SOURCE: power door locks on a 2004 chevy tahoe don't work

The door locks on my 1999 tahoe stopped working and I checked the fuse, which was fine. The problem turned out to be that the fuse for my cigarette lighter was bad and for some reason it also must be working in order for the door locks to work. Put in a new cigarette lighter fuse and the door locks worked again!

Posted on Apr 22, 2010

  • 33 Answers

SOURCE: 2005 chevy tahoe rear door latch won't unlock when

Oil in the latch may help. You may also check the brass contact pins on the door jam. they will be springloaded brass push button style fingers. the door will have a plate that they contact. they get stuck sometimes but most of the time the just tarnish and do not connect well. you can polish them and the plate with a scotch-bright pad (new one) or use some steel wool. Try that and let me know if that helped you.

Posted on Aug 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose which door is causing the door ajar warning on dic for 08 pontiac g6 4cyl 4dr


It should tell you which one .
Driver Door Ajar Malfunction
Passenger Door Ajar Malfunction
If not a scan tool would be the best way.
Ignition ON, observe the scan tool Driver Door Ajar Sw parameter while opening and closing the driver door. The parameter should change between Door Closed and Door Ajar
? If the parameter does not change, refer to Driver Door Ajar Malfunction.
With the passenger doors closed, observe the scan tool Door Ajar Switch parameter while opening and closing each door. The parameter should change between Door Closed and Door Ajar.
? If the parameter does not change, refer to Passenger Door Ajar Malfunction

Ignition OFF, disconnect the harness connector at the driver door latch.
Test for less than 5 ohms between the ground circuit terminal 8 and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance.
Ignition ON, verify the scan tool Driver Door Ajar Sw parameter is Door Closed.
? If not the specified value, test the signal circuit terminal 6 for a short to ground. If the circuit tests normal, replace the BCM.
Install a 3A fused jumper wire between the signal circuit terminal 6 and the ground circuit terminal 8. Verify the scan tool Driver Door Ajar Sw parameter is Door Ajar.
? If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
If all circuits test normal, test or replace the driver door latch

Dec 26, 2016 | Pontiac Cars & Trucks

2 Answers

2003 navigator interior Lights and driving lights won't turn off. Door ajar warning on


Is your 'door ajar' or 'dome light' staying on? Forum members suggest various methods that they fixed their issue. The methods include:
  • Adjusting the dimmer
  • Spraying the switch with a lubricant
  • Replacing the switch
  • Replacing the relay

Sep 28, 2016 | Cars & Trucks

1 Answer

Where is chime module located on 2005 ford taurus


There is no chime module ,there is a speaker inside the instrument cluster.
Door Ajar Chime
The door ajar chime feature is controlled by the smart junction box (SJB). The driver and passenger door ajar switches, and the liftgate are hardwired to the SJB. If any door or liftgate is sensed as being open, and the ignition switch is in RUN/START position, the SJB will process the input and sends a chime request to the instrument cluster over the controller area network (CAN).
Safety Belt Warning Chime
The safety belt chime feature is controlled by the restraints control module (RCM). The driver safety belt switch is hardwired to the RCM. The RCM communicates with the instrument cluster over a hardwire connection. If at any time during the first 6 seconds after the ignition switch is placed in RUN the driver safety belt is sensed as being unfastened, the RCM will process the input, and in turn, sends a chime request to the instrument cluster.
Have the vehicle checked for DTC'S - diagnostic trouble codes ,not OBD 2 codes , the check engine light has nothing to do with this .
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 Instrument Cluster is Defective Instrument Cluster INSTALL a new instrument cluster. REFER to Section 413-01 . B1352 Ignition Key-In Circuit Failure Instrument Cluster Go To Pinpoint Test B . B2477 Module Configuration Failure Instrument Cluster REFER to Section 413-01 .
For a complete list of instrument cluster DTCs, refer to Section 419-10 .


Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 SJB is Defective SJB INSTALL a new SJB. REFER to Section 419-10 . B1352 Ignition Key-In Circuit Failure SJB Go To Pinpoint Test B . B1577 Lamp Park Input Circuit Short to Battery SJB Go To Pinpoint Test E . C1167 Park Brake Actuator Assembly Switch Released Circuit Short to Ground SJB Go To Pinpoint Test F . Your best bet is to have a qualified repair shop diagnose this problem ,what ever it is .
Have the vehicle

May 28, 2016 | Ford Cars & Trucks

1 Answer

Door chimr module loca5ion 2005 taurus


There isn't a chime module , built into instrument cluster !
Door Ajar Chime
The door ajar chime feature is controlled by the smart junction box (SJB). The driver and passenger door ajar switches, and the lift gate are hardwired to the SJB. If any door or lift gate is sensed as being open, and the ignition switch is in RUN/START position, the SJB will process the input and sends a chime request to the instrument cluster over the controller area network (CAN).
Safety Belt Warning Chime
The safety belt chime feature is controlled by the restraints control module (RCM). The driver safety belt switch is hardwired to the RCM. The RCM communicates with the instrument cluster over a hardwire connection. If at any time during the first 6 seconds after the ignition switch is placed in RUN the driver safety belt is sensed as being unfastened, the RCM will process the input, and in turn, sends a chime request to the instrument cluster.
Do you know what C.A.N controller area network is ? Serial data communication bus.
Do How to Diagnose Controller Area Network CAN

May 28, 2016 | 2005 Ford Taurus

1 Answer

I have a 2005 Ford Focus and the fuel light stays on. It is very dim, even when I shut the car off.


Principles of Operation
NOTE: When installing a new instrument cluster, the new instrument cluster must be configured. Refer to Section 418-01 .
The instrument cluster is a hybrid electronic cluster (HEC) which receives and outputs information using both hardwired circuitry and the controller area network (CAN) communication circuits.
It is very important to understand:
  • where the input originates from.
  • all the information necessary for a feature to operate.
  • which module(s) receive(s) the input or command message.
  • if the module that received the input controls the output of the feature, or if it sends a message over the CAN to another module.
  • which module controls the output of the feature.
The instrument cluster carries out a prove-out when the ignition switch is turned from the OFF to the RUN position to verify the integrity of the warning indicators. The charging system warning indicator, the low oil pressure warning indicator and the malfunction indicator lamp (MIL) illuminate when the key is turned to the ON position, and then turn off when the engine is started. The seat belt warning indicator proves-out for 60 seconds and then turns off, or turns off when the seat belt is fastened. The following indicators prove-out when the key is turned to the ON position:
  • door ajar warning indicator (3 seconds)
  • anti-lock brake system (ABS) warning indicator (3 seconds)
  • O/D OFF indicator (3 seconds)
  • air bag warning indicator (6 seconds)
  • brake warning indicator (3 seconds)
  • door ajar warning indicator (3 seconds)
  • shift up indicator (3 seconds)
  • low fuel warning indicator (3 seconds)
  • traction control indicator (3 seconds)
  • check fuel cap indicator (3 seconds)
  • passive anti-theft system (PATS) indicator (3 seconds)
Low Fuel Warning Indicator
The instrument cluster utilizes fuel level data supplied by the hardwired fuel pump module to control the low fuel warning indicator, which illuminates when the fuel drops to a pre-determined level.
Your best bet is to take this to the Ford dealer , unless you have Ford IDS - factory scan tool to diagnose this
Your best bet

Dec 29, 2015 | Ford Cars & Trucks

1 Answer

Liftgate door ajar warning light


Have someone stand at liftgate and press the switch in. If the warning goes off, then your switch just needs adjusting or the small flat block that acts like your partners finger is missing or misaligned. The door hinge pins should not be a problem unless there is damage to the area or a teenager was using the door as a tarzan swing. The BCM is a possibility (rare), but it is much more likely a contact problem behind the switch - ie. a loose connection, chaffed wire or short. Good luck.

Apr 20, 2014 | 2007 Chevrolet Tahoe

1 Answer

2005 jeep wrangler when i turn lights on beeping starts


did you RTM read the operators guide yet,
it tells you why all beeps beep and what lamps flash, (warning) and why. did you?
you turn on, the head lights, (what about 1st click , parking lights"?)
and does the dash cluster, show warnings of any kind?

if a door is ajar the system will think, you are exiting veh. with lights on and tell you, buy beeping ,etc.
but on my jeep it says on the dash DOOR, or on EVICs, (not yours)
the newer car even tells what door IS AJAR.
mine on shows , "DOOR"
the operator guide will say, check all doors for ajar, and get warning clear before driving....etc.

if you lost the guide here it is for free

http://justgivemethedamnmanual.com/jeep/jeep-wrangler-owners-manuals/

click the 05 link
ignore beeps, there are just too many .. i look at the cluster and learn to read it..
my newer jeep 08 can produce 1000s of errors,,,,, possible.
in fact the intent it to beep to tell the driver to look at the cluster
for in depth, causes.
see chapter starting on page 136'

once sound it makes is Check gauges chime. so check them.
and headlamps left on
and door ajar.

page 63
NOTE: If the driver's door is left open, and the headlights
or parking lights are left on, the "High Beam
Indicator Light" will flash and a chime will sound.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned off, a chime will sound when the driver's door

its a crude system, and evolved to complex in 2007.
"DOOR" or RF-door , on mine.
or

NOTE: A tone will chime if the turn signals are left on
for more than 1 mile (2 km).

search manual for
"chime will sound"

Mar 21, 2014 | 2005 Jeep Wrangler

1 Answer

2007 Tahoe I get warning that hood is open when it is not. Interior lights come on while driving and won't shut off for a time, vehilce is parked and locked for hours and alrm sounds and lights flash...


{: ) There is a certain GM bulletin that can be related to this issue. This may be due to moisture intruding the door latch switch. This may affect the electrical function of the latch and cause the conditions you just mentioned. And the replacement version has a new latch cover material.
The vehicle's body control module (BCM) monitors inputs coming from all the doors. Obviously at one point it is receiving false signals that can trigger your alarm and interior lights, and even ajar messages on your cluster. The question now is which of them is giving this false signals. Is it from a component or the wirings?
Whether your situation is related under this bulletin or not, you can do your own visual and manual test to determine which door is the culprit. But in case you have a hard time figuring it out, it is better to have it tested by a GM scan tool. It is like you have another BCM in your hands, but you can be able to monitor and read the datas on the screen. It will be much faster to isolate the trouble.

Aug 09, 2011 | 2007 Chevrolet Tahoe

1 Answer

My liftgate ajar warning light comes on after car is started. however liftgate is latched. any ideas?


try rolling down a window or leaving a door open, shut liftgate hard. see if it still shows liftgate ajar. on my explorer the seals in door and windows shut so tightly that it was almost impossible to get the gate closed completely with doors closed and windows up.

if this doesn't help then you might need a new switch on it.

Feb 05, 2010 | 2003 Lincoln Navigator

3 Answers

How can I fix a door adjar error on a 1999 Lincoln Continental? When the drivers door is shut, the warning comes on and the dome lights remain on. I don't want to spend money to replace the sensor, but can...


I suspect you have a bad door ajar switch on one of your doors.

The switch is on the door latch. try pushing each door in with your hand one at a time and see if the warning goes away.
The Lighting control module is $500 and controls a lot of the vehicle functions. It is part of the headlamp switch. It has to be configured by the dealer with his NGS tester before it will work. Ebay has them cheap sometimes. Only buy Continental LCM for your model year.



info
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
-----------------------------------
Visual Inspection Chart Mechanical Electrical
  • Door ajar switches.
  • Fuse junction panel fuse 28 (10A), 4 (10A), 5 (10A).
  • Power distribution box fuse 6 (60A).
  • Circuitry.
  • Damaged or corroded connectors.
  • Lighting control module (LCM)
  • Driver door module (DDM).
  • Virtual image cluster (VIC).
  • Restraint control module (RCM).
  • Low tire pressure module.

------------------------------------------------------------
  • The Door Ajar Chime Does Not Operate Properly
  • LCM.
  • Driver door ajar switch.
  • Passenger door ajar switches.
  • Key warning switch.
  • Circuitry.

-------------------------------------------------------------
remove the door trim panel to access the door ajar switch.

0339bdb.gif
Remove the door open warning switch by turning it counterclockwise.
----------------------------------------------------------------------------
Trim Panel —Front Door Removal
  1. Remove the screw cover.
  1. Remove the screws.
  1. Remove the front door trim panel (23942) from the door.
  1. Disconnect the electrical connectors and remove the front door trim panel.
Installation
  1. Follow the removal procedure in reverse order.

Aug 28, 2009 | 1999 Lincoln Continental

Not finding what you are looking for?
2005 Chevrolet Tahoe Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...