Question about 2000 Mazda B-Series

Open Question

Mazda e 2000 torque settings

Tappet settings & clearance & torque sequence

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

3dmaster
  • 183 Answers

SOURCE: Mazda MX5 tiorque settings

Dear Customer,

Its all about firing speed & firing sequence,

tr yo to got to showroom or branded certified mechanic or you can do yourself if have experience about all this settings,

this will defenatly increase your 100% torque,

But do all this with care,takes time,

THNX

Posted on May 20, 2008

ZJLimited
  • 17970 Answers

SOURCE: I need the 2003 Mazda

zjlimited_34.jpg

Fig. Loosen the remaining camshaft cap bolts using this sequence-2.3L (KJ) engine


zjlimited_35.jpg

Fig. Tighten the camshaft cap bolts using this sequence-2.3L (KJ) engine

Posted on Nov 09, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2000 Mazda Drifter 2.5 Turbo

Mazda B2200, B2500 and B2600 (6th Generation).

In model year 1998, Mazda B series renews its own international markets. Production at the plant AutoAlliance Thailand began in May 1998. This model is also sold as the Ford Ranger in Europe and Asia, and the Ford Courier in Australia and New Zealand. Production started this year in the factories of companies AutoAlliance Thailand and Ford Motor Philippines. Versions CKD are also assembled in South Africa, Ecuador and Colombia.

The van is sold in over 130 countries under a variety of names. Along with the emblems of Fighter and Ranger in Southeast Asia (except Singapore, which served as the flagship models Proceed Japan), was sold as the Mazda Bounty and Ford Courier in New Zealand, Mazda Bravo in Australia, and Mazda Drifter in South Africa.

Engine options:
2.2 L 2.2 L (2.184 cc) 85 hp (63 kW)
2.5 L (1.998 cc) turbo diesel 118 hp (88 kW)
2.6 L (2.606 cc) 121 hp (90 kW)


zjlimited_1152.jpg

Fig. Tighten the exhaust manifold bolts in 2 stages

To install:

  1. Clean the mating surfaces on the exhaust manifold and the cylinder head.
  2. Install a new gasket and the exhaust manifold. Torque the bolts in sequence as follows:
    1. 16 ft. lbs. (23 Nm).
    2. 59 ft. lbs. (80 Nm).

Hope helps.

Posted on May 01, 2011

emissionwiz
  • 75222 Answers

SOURCE: 2000 model mazda 323 astina cylinder head bolt torque specs

Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Posted on Feb 16, 2012

cansmo
  • 2431 Answers

SOURCE: valve clearence settings mazda protege 2003

This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Posted on Feb 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

What is the tappet clearance and torque setting for hyundai atos 1.1 2007


valve clearance is inlet .02mm hot. exhaust .025 mm hot cyl head torque is cyl head torque stage1 30-35nm stage2 60-70nm stage3 run engine for 15 minutes. stage 4 tighten further 70-75 nm

Dec 15, 2016 | 2007 Hyundai Atos 1.1

1 Answer

What are tappet clearances and sequence of adjusting on an unidentified engine?


unidentified means we can not assist you . try a local dealer

Feb 25, 2016 | Cars & Trucks

1 Answer

Where can I found torque settings for mazda etude 1600 ie 2000 model


buy a hynes, gregories or any other work shop manual for your vehicle . They will have all the torque settings and the proper sequence for tightening the bolts.

Apr 04, 2013 | Cars & Trucks

1 Answer

Mazda 6.2 engine valve clearance


tappet clearance for this engine i wouldnt know offhand but 12 inlet and 14 exhaust will suffice without doing any damage and 25th for the plugs

Apr 15, 2012 | Mazda Cars & Trucks

1 Answer

Valve clearence settings mazda protege 2003


This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Feb 24, 2012 | Mazda Protege Cars & Trucks

2 Answers

Mazda MX5 tiorque settings


Dear Customer,

Its all about firing speed & firing sequence,

tr yo to got to showroom or branded certified mechanic or you can do yourself if have experience about all this settings,

this will defenatly increase your 100% torque,

But do all this with care,takes time,

THNX

May 20, 2008 | Mazda MX-5 Miata Cars & Trucks

Not finding what you are looking for?
2000 Mazda B-Series Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...