Question about Chevrolet Cars & Trucks

Open Question

2009 suburban wont start/ dtc po25a

No fuel pressure

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

csmock132
  • 4669 Answers

SOURCE: truck wont start

Check the fuel pressure. It needs to be 55 or higher no less.

Posted on May 06, 2009

czaa
  • 4514 Answers

SOURCE: Car wont start 2002 mustang gt dtc 1230 1233 codes

chec fuel pressure regulator it is in line of fuel next to engine-inpec for leaks insystem also-if u aquire a svc manual there is a list of codes or ask tech at dealer-look over ignition area to rule out

Posted on Sep 13, 2009

vetteman3002
  • 2299 Answers

SOURCE: MY 1999 SONOMA START BUT

Have you checked the timing? It sounds like it may have jumped time.

Posted on Sep 21, 2010

  • 520 Answers

SOURCE: After running for about 10-30

first thought is that the catalytic converter may be plugged. when plugged the engine will run until it builds up enough back pressure to kill the engine. after it sets a while the pressure is released and the car will start again. you should be able to start it up and observe how much force your exhaust pipe has. it should be strong at first then decrease to almost nothing before it dies. try that and check back.
remember that any of the new parts could also be bad so you may need to do a pressure check on your fuel pump

Posted on Jan 29, 2011

  • 638 Answers

SOURCE: 99 cavalier dtc p0452 fuel

did you try to remove the code # with a diagnostic code retrieveing tool, this will remove the light from being on in the system, providing the computer is functioning properly, if you do not have the tool to do this with, then disconnect your positive battery cable, for about 1 minute, then reconnect it back up, and see if light is out. you will have to reset your vehicles clock, and possibly some radio functions.

Posted on Apr 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2009 chevy tahoe fuel pump wont shut off


The fuel pump control module is controlled by the ECM - engine control module , Possibility of DTC'S stored ! You need to take to Chevy Dealer !
The engine control module (ECM) supplies voltage to the fuel pump control module (FPCM) when the ECM detects that the ignition is ON. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in Crank or Run. While this voltage is being received, the FPCM closes the ground switch of the fuel pump and also supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.

Apr 22, 2015 | 2009 Chevrolet Tahoe

1 Answer

1996 suburban with 5.7l have good fuel pressure, sparks at the plugs, cranks with starter fluid but wont crank when i disconnect the crank sensor.


when you say good fuel pressure is it 55 psi with the key on and engine off? any thing less then 50 psi will not start the engine. if the engine starts with starter fluid then the problem is in the fuel system.

Aug 13, 2011 | 1997 Chevrolet Suburban

2 Answers

If i let my 96 suburban sit for a couple of days it wont start but if i drive it everyday it starts up fine


If it cranks but won't start you might have a fuel pump issue that is intermitent or a plugged fuel filter. You can check this with a pressure gauge at the end of the fuel line.

Jun 30, 2010 | 1996 Chevrolet Suburban

4 Answers

1998 5.9 jgc cranks but wont start.starts with a shot of ether,is this bad fuel pump


could be the pump? or the pump relay? or even a clogged fuel filter crack the line going into the rear of the filter and crank the motor if fuel comes out ? change the filter if no fuel then? check the relay and or change the pump

Jan 21, 2010 | 1998 Jeep Grand Cherokee

1 Answer

2003 chevy suburban wont start in the morning after sitting over night, if it has less than half a tank of gas?


it sounds like you have a fuel line problem inside the tank,maybe a pinhole, once fuel level gets below pinhole the line loses pressure. once it loses pressure you have to keep turning switch on & off too get pressure built back up.

Jan 12, 2010 | 2003 Chevrolet Suburban 1500

2 Answers

1999 GMC Suburban Wont Turn Over


It sounds like you have a security problem, I had the same thing it would fire and run for half of a second and then that was it if anything at all. Had the security system rebooted, now it starts and runs fine.

Jun 07, 2009 | 1999 GMC Suburban

1 Answer

98 chevy suburban wont completely start


check for spark at plugs or fuel pressure need both torun

Feb 26, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

Truck wont start


Check the fuel pressure. It needs to be 55 or higher no less.

Feb 19, 2009 | 1997 Chevrolet Suburban

1 Answer

96 chevy 1500 suburban wont start


check the catalytic converter i had the same problem with my suburban and mine was a clogged converter.

Jan 19, 2009 | 1996 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...