Question about 2000 Toyota Sienna

1 Answer

Car wont start

I was driving on freeway it turn off on me, car battery is good, starter was tested and is also good, and when i open the ignition switch it makes a weird noise sounds by near the driver side.

Posted by on

  • sonic super Jan 13, 2013

    ok so i ts not the starter or battery, nor the relay...next to test are the cables and the ignition switch, just my concern is a noise when left keys in the on position.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 937 Answers

May be you should make a diagnostic and the tool autel maxidas ds708 may can help you

Posted on Jan 12, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: 1994 Toyota Tercel Starter Problems

sounds to me that you have an igniton problem not a starter problem and or if you have or had an alarm system could be cause if u do give me feedback and i will explain but seems that your starter is fine from what u say but if you think in terms of the elemts to start a vehicle batery gives pwoer to ignition which sends to starter which gives spark etc i would check you ignition system something is causeing a short and not alowing starter to function

Posted on Feb 10, 2009

  • 14 Answers

SOURCE: engine died & wont start no spark ignition coil tested good

try your ignition module in the distributor much more likely. just install rebuilt distributor if that is the problem , if you just replace module the main distributor assem will **** out shortly after.
Make sure you check for broken timing belt also it is one of those two!

Posted on May 27, 2009

Sgt Fluffy
  • 157 Answers

SOURCE: 1991 toyota camry front drivers side makes noise while driving

It's the left front wheel bearing. Take it to your favorite mechanic if you have one, any good tech can do it, but he/she could run into complications with a car of that age. (The hip bone's connected to the thigh bone, the thigh bone's connected to the knee bone, etc, and there's probably a good share of corrosion down there).

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key won't turn the ignition 2000 s-series saturn


Test the battery if it does absolutely nothing when trying to turn over, if battery is good, check for a bad fuse possibly, check leads from ignition control module to the starter, possibly could be a bad ignition switch in the car. if the car attempts to turnover but wont start, you could be looking at a bad starter, fuel pump. Before you go too far into it though, just get the battery tested better to start small with these things, Good Luck!

Dec 04, 2016 | Saturn Cars & Trucks

2 Answers

Ford ranger wont start


run fault codes and check for cam/crank sensor. check that the cam shaft is turning( broken cam belt) check operation of the immobiliser. Check that the fuel pump is working.

Jan 02, 2014 | Cars & Trucks

1 Answer

I have a 2003 Saturan Ion that won't start


Hi, this is what you should do when your car won't start. Diagnosing a no-start condition requires a logical approach to figuring out what might be preventing your car from starting. First, if the engine won't even crank over when you turn the ignition to START, your car obviously won't start.
When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

If the engine fails to crank, there is a fault in one of the components in the battery/ignition/starter circuit. Check it out.....
  • Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
  • Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
  • Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
  • Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
  • Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
  • Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
  • Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
  • Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
  • Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
  • Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Dec 02, 2010 | 2003 Saturn ION

1 Answer

1993 suburban is not starting and it is not the battery. What could it be?


IF BATTERY CABLES OLD THEY WILL CAUSE POOR GROUND HIGH RESISTANCE IN STARTER CIRCUIT CAUSING STARTER NOT TO CRANK ENGINE.CHECK TO SEE IF DASH LIGHTS AND GAUGES WORK WHEN YOU TURN ON IGNITION SWITCH IF NO CHECK IGNITION FUSES.IF FUSES OKAY IGNITION SWITCH IS OPEN NEED REPLACING.NOW IF BATTERY VOLTAGE IS 12.6 VOLTS, BATTERY CABLES GOOD AND IGNITION SWITCH AND FUSE OKAY. STARTER SOLENOID OR STARTER FAULTY.REMOVE STARTER TAKE TO ANY AUTO PARTS STORE THEY WILL TEST STARTER.TURN OFF RADIO BEFORE REMOVING NEGATIVE BATTERY SO YOU WONT LOCK OUT RADIO.

Nov 02, 2010 | 1993 Chevrolet Suburban

2 Answers

Engine will not turn over. lights, horn, everything else works, no clicks, no nothing, but it will not turn over.


You're describing a no rotation issue and not a no start issue correct? If you dont hear/feel the starter relay clicking, it eliminates everything in the circuit to that point meaning the ignition switch, Transmission Range Sensor (TRS) (you don't have a neutral start switch unless you have a rare manual transmission), ground input from the Powertrain Control Module (PCM) to the starter relay coil, and starter relay are good. Based on what you've said that leaves the primary battery cable from the battery to the starter, and the wire from the starter relay to the starter solenoid contact on the starter. Have you checked their continuity? One more voltage to check at contact 30 (input volts from battery to starter relay contacts) on the starter relay socket. Should see 12vdc all the time.

You should check the battery. The true test is a load test. Does jumping the battery using jumper cables make any difference? If it starts, change the battery. I take it to check the starter you jumpered the solenoid contact on the starter to the battery correct? Have you tried wiggling the battery cables as you turn the key? They can corrode and fail internally. Are the engine and chassy ground connections clean and tight?

Jul 14, 2010 | 2004 Dodge Caravan

1 Answer

Wont start--pulled starter bench tested ok


check your ignition did one of these before changed 3 starters before finding out it was ignition switch not making connection in switch good luck

Feb 07, 2010 | 1997 GMC Jimmy

2 Answers

Truck wont start, new battery, good fuses, bench tested starter they say its good, cables look ok.Turn ignition and dash lights come on can hear fan motor running.


test starter solinoid wire from harness, with a helper put test light on wire get friend to turn key to start, light should light up, wires at the bottom of engine may (look) fine

Apr 25, 2009 | 1989 Chevrolet C1500

1 Answer

Wont start


i see that you said the battery and starter is good have you had the alternater tested and replace the drive belt and also take 12 volt tested to see if you have power going to the starter

Feb 01, 2009 | 1999 Volkswagen Jetta

Not finding what you are looking for?
2000 Toyota Sienna Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...