Question about 2008 Saturn VUE

1 Answer

Cannot shift transmission in manual setting - 2008 Saturn VUE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 74 Answers

Check it shifter cable on the transmission it may be damaged

Posted on Jan 12, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dont have key need to get it into neutral


Hi,
Set the parking brake - so it doesn't roll away!
In the owner's manual it should show how to bypass the transmission interlock system. If no manual, there is likely a small access hole - possibly w/a cover - near the transmission shift lever. Insert a flat head screwdriver (you set the parking brake yet?) and it'll release the shift lever to move it to Neutral.
GL,
TD

Mar 29, 2016 | 2004 Nissan Quest

1 Answer

1988 Dodge Ram 50 Automatic shifts into park reverse and neutral. But physically won't go into drive gears.


Disconnect shift cable from transmission linkage and try to manually put transmission in drive gear ( make sure wheels chocked/park brake on ). If transmission goes into drive gear, suspect a shift cable or shifter assembly problem. If you can't manually shift into drive gear by hand with cable disconnected, suspect internal transmission/shift linkage issue

Mar 10, 2016 | Dodge Cars & Trucks

2 Answers

Truck will not exceleratein drive.It will go,it just won't excelerate


transmission either slipping lack of transmission fluid or transmission has failed.check transmission manual shift linkage.make sure manual shift linkage not disconnected or damaged.make sure manual shift adjustment correct.

Jun 17, 2013 | Cars & Trucks

1 Answer

Why won't 2003 pontiac grand prix. shifter come out of park?


Shift - interlock system problem .
Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission park lock solenoid
• The automatic transmission shift lock control switch
• The transmission range switch
With the ignition in the ON position, battery voltage is supplied to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The transmission range switch provides a path to ground for the automatic transmission shift lock control solenoid in the PARK position. With the automatic transmission shift lock control solenoid energized the shift lever is mechanically locked in the PARK position. When the driver presses the brake pedal, the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to move from the PARK position. When the shift lever is out of the PARK position the controlled ground contacts in the transmission range switch open. This prevents the automatic transmission shift lock solenoid from energizing when the vehicle is out of the PARK position.

Jul 04, 2017 | Pontiac Grand Prix Cars & Trucks

1 Answer

Transmission pressure switch manifold fault explanation p1810


Hi there:
The automatic Transmission Fluid Pressure (TFP) manual valve position switch consists of five pressure switches (two normally-closed and three normally-open), and a transmission Fluid Temperature (TFT) sensor combined into one unit. The combined unit mounts on the valve body.
The Powertrain Control Module (PCM) supplies ignition voltage for each range signal. By grounding one or more of these circuits through various combinations of the pressure switches, the PCM detects which manual valve position you select. The PCM compares the actual voltage combination of the switches to a TFP manual valve position switch combination chart stored in memory.

The TFP manual valve position switch cannot distinguish between PARK and NEUTRAL because the monitored valve body pressures are identical. With the engine OFF and the ignition switch in the ON position, the TFP manual valve position switch indicates PARK/NEUTRAL. Disconnecting the AT inline 20-way connector removes the ground potential for the three range signals to the PCM. In this case, with the engine OFF, and the ignition switch in the ON position, D2 will be indicated.

When the PCM detects an invalid state of the TFP manual valve position switch circuit by deciphering the TFP manual valve position switch inputs, then DTC P1810 sets.Action Taken When the DTC SetsThe PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in, which the Conditions for Setting the DTC are met.The PCM commands D2 line pressure.The PCM commands a D4 shift pattern.The PCM freezes transmission adapt functions.The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.The PCM stores DTC P1810 in PCM history during the second consecutive trip in, which the Conditions for Setting the DTC are met.Since the computer does not know what gear range the transmission is shifted into, it defaults to a higher line pressure to protect the transmission. It also commands the transmission as if it were in the D4 position. The transmission will still shift normally through all the gears, shifts may be more firm than normal. No damage will occur to the transmission if driven even for prolonged periods with this dtc set. It is far more likely that the loss of transmission fluid damaged the transmission.

Hope helps.

Mar 21, 2012 | 2002 Pontiac Grand Am

1 Answer

HAVE A 1989 FORD F-150 WITH AUTO TRANS THAT YOU CAN'T SHIFT OUT OF THE "PARK" POSITION AT THE STEERING COLUMN. THE TRANY CAN BE SHIFTED AT THE TRANS WHEN LINKAGE IS DICONNECTED.I THINK THE...


What trans? AOD? This is 1992 F Series, all I have.

Shift Controls, Automatic Transmission The transmission shift control linkage or cable transfers the transmission operating mode from the selector lever to the transmission. The indicated transmission position on the steering column is transferred to a shift lever on the bottom of the steering column. On vehicles equipped with cable-operated shift systems, the indicated position of the transmission selector lever is transferred to the transmission through the shift cane, then to the cable, and down to the transmission manual shift lever at the transmission. On vehicles equipped with shift rod assemblies, the rod transfers the indicated transmission selector level position through a bell crank assembly to a control rod. The control rod transfers the indicated position to the transmission assembly.
----------------------------------------------
Automatic Transmission Manual Linkage Adjustments
  1. With the engine stopped and the parking brake applied, place the transmission selector lever at the steering column in the D (DRIVE position) for C6 applications and in the (D) (OVERDRIVE position) for AOD and E4OD applications, and hold against the D or (D) stop by applying a three-pound force to the selector lever knob.
  1. Loosen the shift rod adjusting nut at point A. Refer to the following illustrations.
  1. Shift the manual lever at the transmission into the (D) (overdrive) position for E4OD, by moving the lever all the way rearward, then forward two detents.
  1. With the selector lever and transmission manual lever in the(D) position, tighten the nut at point A to 17-24 Nm (12-18 ft-lb) torque. Use care to prevent motion between the stud and rod.
  1. Remove the three-pound force from the steering column selector lever knob.
  1. Operate the shift lever in all positions to make certain that the manual lever at the transmission is in full detent in all gear ranges. Re-adjust the linkage if required.
  1. On F-Super Duty Chassis Cab and Motorhome and Commercial Chassis recheck for correct operation of the automatic transmission selector indicator (PRN(D)21). Refer to Section 11-04A, Steering Column, Shift Rod Within Tube. ani_caut.gif CAUTION: Under no circumstances will it be permissible to adjust linkage in any position other than the(D) position for E4OD applications.
---------------------
Automatic Transmission Shift Cable Adjustment
  1. From inside the vehicle, place the column shift select lever in the DRIVE position (C6) of the OVERDRIVE (AOD and E4OD). Hang a three-pound weight on the selector lever.
  1. Raise vehicle on a hoist.
  1. Remove the shift cable from the transmission lever ball stud.
  1. Pull down the lock tab on the shift cable body.
  1. Position the transmission shift lever in the DRIVE position (C6) or the OVERDRIVE position (AOD and E4OD). This is three detents from the front-most lever position with the first position counting as one.
  1. Connect the cable end fitting to the transmission lever ball stud.
  1. Push up on the lock tab to lock the cable in the correctly adjusted position.
  1. Lower vehicle down from hoist and remove the three-pound weight from the column shift select lever.
  1. After making the adjustment, check for park engagement. Check the transmission control lever in all detent positions with the engine running to make sure correct detent/transmission actions. Readjust if necessary.

Jun 21, 2011 | Ford F-150 Cars & Trucks

1 Answer

Any way to convert an auto transmission into a manual transmission. The original automatic needs replacing and would like to put a better manual transmission in it


CHEAPER TO REPLACE TRANSMISSION THAT TO CONVERT IT INTO MANUAL.YOU HAVE TO PUT IN A CLUTCH MASTER CYLINDER AND SLAVE CYLINER.YOU HAVE TO PUT IN CLUTCH PEDAL IN FLOOR BOARD.YOU HAVE TO CHANGE TRANSMISSION SHIFT LEVER TO MANUAL STICK SHIFT.YOU LOOKING AT A HEAD ACHE.BETTER AND CHEAPER TO REPLACE TRANSMISSION.IF YOU GO MANUAL.YOU WILL SPEND MORE MONEY TO GET IT SET UP AND BUY PARTS TO GET IT TO WORK.

Apr 18, 2010 | 1994 Buick Skylark

2 Answers

Can a 1998 4x4 S-10 blazer be dinghy towed?


Yes it can, just place your Transfer Case in Neutral position.
Shifting into NEUTRAL
To shift the transfer case to NEUTRAL do the following:

Make sure the vehicle is parked so that it will not roll.
Set the parking brake.
Start the vehicle or turn the ignition to RUN.
Connect the vehicle to the towing vehicle.
Put the transmission in NEUTRAL (N).
Shift the transfer case to 2HI.
Simultaneously press and hold the 2HI and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete.
Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, or FIRST (1) for vehicles equipped with a manual transmission.
Turn the ignition to LOCK.
Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles with a manual transmission.
Release the parking brake prior to towing.

Shifting Out of NEUTRAL
To shift out of NEUTRAL:

Set the parking brake and apply the regular brake pedal.
Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off.
Press the button for the desired transfer case shift position (2HI, 4HI, AUTO 4WD or 4LO).
After the transfer case has shifted out of NEUTRAL the red light will go out.
Release the parking brake.
You may start the engine and shift the transmission to the desired position.
Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes.

NEUTRAL: Shift the vehicle's transfer case to NEUTRAL only when towing your vehicle.
Good luck and hope this answers your question.

Jan 30, 2010 | 1998 Chevrolet Blazer

3 Answers

I CAN NOT SHIFT THR TRANS INTO NUTRAL SO I CAN TOW IT BEHIND MY MOTOR HOME. IT WILL SHIFT INTO 2H, 4H, 4L


Shifting to NEUTRAL
To shift the transfer case to NEUTRAL, first make sure
the vehicle is parked so that it will not roll:
1. Set the parking brake.
2. Start the vehicle.
3. Connect the vehicle to the towing vehicle.
4. Put the transmission in NEUTRAL (N) or have
the clutch pedal pressed for vehicles with
manual transmission.
5. Shift the transfer case to 2HI.
6. Simultaneously press and hold the 2HI and
4LO buttons for 10 seconds. The red NEUTRAL
light will come on when the transfer case shift to
NEUTRAL is complete.
7. Shift the transmission to REVERSE (R) for one
second, then shift the transmission to DRIVE (D)
for one second or FIRST (1) for vehicles with
manual transmission.
8. Turn the ignition to OFF.
9. Place the transmission shift lever in PARK (P) or
FIRST (1) for vehicles with manual transmission.
10. Release the parking brake prior to towing.

************************

Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Start the vehicle with the transmission in PARK (P)
or FIRST (1) for vehicles with manual transmission.
3. Press the button for the desired transfer case position
(2HI, 4HI, AUTO 4WD or 4LO).
4. Put the transmission in NEUTRAL (N) or press the
clutch pedal for vehicles with manual transmission.
5. Shift the transmission lever to the desired position.
After the transfer case has shifted out of NEUTRAL,
the red light will go out.
6. A re-engagement sound is normal when shifting out
of NEUTRAL.

Jan 22, 2010 | 2000 GMC Jimmy

1 Answer

Auto Transmission


Try shifting the trans manually through the gears and see what happens,doesnt cost anything so,possibility valves are sticking in the valvebody after sitting so long,and manually shifting the car will force some of them to stroke in their bores unless REALLY stuck.Could also be shift solenoids.Scan for diagnostic trouble codes.A bad solenoid will have set a trouble code.Just FYI,1991 was the first year Ford went to all electronic trans,i had a 91 Sable.

Jul 26, 2008 | 1991 Ford Taurus

Not finding what you are looking for?
2008 Saturn VUE Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...