Question about 2011 Mazda BT-50 L-Cab

Open Question

Install lower front grill 2011 mazda cx7

Need to remove and replace 2011 mazda cx7 lower grill

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: how do i remove the lower ball joint on a mazda

Big hammer and a fork made for such a job. No fork to barrow? use a large flat head screw driver and be patient. Remove the tire. Jack the truck up and use jack stands. Use parking brake. The work may take a few hours. getting the new ones on are easier

Posted on Aug 09, 2009

Ad
Hrnsly
  • 154 Answers

SOURCE: Timing chain broke on a 2007 cx7 w 65K miles

you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Posted on Aug 12, 2009

  • 213 Answers

SOURCE: how do i replace a headlamp on a 2007 mazda cx7

un plug the cable socket at the back side of the headlight then remove the rubber cover at the same place and then there is a steel wire clip carefully remove it (as you have to put it back again) the lamp can be removed easily you have to put the new one in the same direction again so remember what you remove

Posted on Jan 20, 2011

  • 3 Answers

SOURCE: I cannot remove the push pins in the wheel weel on

TRY TO PRY WITH A FLAT SCREWDRIVER BETWEEN THE SCEW AND WASHER DURING YOU UNSCREW THE PHILLIPS ...IT SHOULD BE OK....

Posted on Jan 29, 2011

  • 1252 Answers

SOURCE: We were told we have

Are you sure they said EGR valve?..as far as i can see, there is no egr valve on this vehicle ???

Posted on Jun 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2011 mazda cx7 turbo spark plug #3 miss fire. why does the motor have to be replaced or rebuilt?


Motor has to be replaced or rebuild in case you have low pressure in one of its cylinders. Is that your case?

May 28, 2017 | Mazda Cars & Trucks

1 Answer

How to remove a L/Front fender on a 1996 Mazda 626


Fenders are bolt on. Remove the plastic inner wheel well. Rais the hood. Remove bolts along too, in door jamb and inner wheel well. Most vehicles also require removing the front bumper cover, headlight assembly and sometimes the grill. You should be able to see the bolt hole locations on the replacement fender. Once you install it do not tighten up the bolts. You'll need to align the fender til the hood to get a narrow consistent seam then tighten the bolts.

Feb 10, 2017 | Mazda Cars & Trucks

1 Answer

Replace outer front door handle Mazda cx7 2010 model


Hey, I just use a metal zipstrip. Cheap and easy. Look on youtube for Prizm handle replacement. You basically slip it under the current handle and slip it in the zip buckle to make a loop. It's ghetto but works and does not use duct tape unlike most Red Green type "solutons".

Feb 01, 2015 | 2010 Mazda CX-7

2 Answers

My 2008 Mazda CX7 is making a rattling noise when I turn left and right. What is causing this?


If it happens only when you turn, You need to replace both front axles. Hope this works.

Jun 18, 2014 | 2007 Mazda CX-7 Grand Touring

1 Answer

How to change key fob battery in 2011 Mazda cx7


Most key fobs have a key way in the middle of the outside of them you have to take a screw driver and pry them open to get at battery at least that was how it was for my dodge .

May 27, 2014 | 2010 Mazda CX-9

1 Answer

How to replace nissan murano 2011 front driver side turn light


Lift hood, remove grill plastic screws on top, jack car left hand side, remove corner screw on end of bumper, undo lower splash shield screws, slide bumper away from car {about 4 inches}, remove,top bolts on headlight and lift out, the is a locating slot that you will need to manipulate it from, assembly is the reversal. good luck.

Oct 20, 2013 | 2007 Nissan Murano SE

1 Answer

Replacing struts on Mazda CX7


There are 3 Nuts inside the Engine Compartment, There is one Bolt on the Lower Arm and you have to remove the ABS and Torsion Rod. You need a Spring Compressor to do this job.

Apr 15, 2013 | 2007 Mazda CX-7

2 Answers

How do I change the bulb in the low beam headlight in my 2007 Mazda CX7?


Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.

Nov 04, 2009 | 2007 Mazda CX-7 Grand Touring

3 Answers

Timing chain broke on a 2007 cx7 w 65K miles


you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Aug 03, 2009 | 2007 Mazda CX-7 Grand Touring

Not finding what you are looking for?
2011 Mazda BT-50 L-Cab Logo

Related Topics:

454 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...