Question about Cars & Trucks

1 Answer

I need help hooking up new headlights, with halos and LEDs, i nned them to turn on right wen the car turns on... Not wen i turn lights on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,669 Answers

For that you will need to be able to do some serious wiring. You will need to find a relay in the engine compartment fuse/relay box that turns on when you turn on the key, like the electric fuel pump relay, for example. Next you will need to calculate the amperage draw of all of the lights you are going to hook up. If the fuse for the relay you chose is smaller than the amperage you need to serve both the fuel pump and the lights then you will need to make a fuse connection at a spare in the fuse box to connect to the new relay output and input (see below). The fuel pump relay has control and supply wires on it. The supply wires actually supply the power to the fuel pump. The control wires simply turn on the relay when you turn on the key in the ignition. You need to hook up the control wires of the fuel pump relay to the control wires of the new lights relay. As stated earlier, the supply wires are then hooked to the relay and, in turn to the supply fuse. Make certain that you use some heavier wire for the supply circuits. Thinner wires may be substituted for the control wires. Solder at the fuse box side and use spade connectors at the lights side...good luck!

Posted on Jan 11, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 12 Answers

SOURCE: when my truck is running sometimes my headlights turn off

you need a headlight switch I take it your headlight switch and turn signal switch is made into one.

Posted on Jan 24, 2009

sowhtlshvugt
  • 15 Answers

SOURCE: my dash go wen i turn my headlights on what do i

do what????? what the hell are you trying to say that it does when switch is turned on....

Posted on Sep 13, 2009

  • 1608 Answers

SOURCE: Both headlights stopped working. Need to turn on

You probably have a bad switch.If your hi beams work then the fuse is good.

Posted on Jan 07, 2010

  • 100 Answers

SOURCE: Headlights

Go to carhelpsite.com it is free as long as you click on 2 of the ads at the website then your questions will be answered by an ASE certified mechanic,you don't have to buy or fill out anything on the ads,so help keep the site free.

Posted on Apr 14, 2010

noranda21
  • 1547 Answers

SOURCE: I have installed both aftermarket headlights and

check wireing may be wired wrong them head lights may not be compatable with that setup

Posted on Dec 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just instalked a new stereo could this have anything to do with my dash lights and tail lights blowing the fuse wen i turn on the headlights


Yes, you could have hook the light wire to a ground. Light wires are usually a dark brown. Not hard to get them mixed up, with low or no lighting when you installed the radio.

Jan 05, 2015 | Cars & Trucks

1 Answer

Aftermarket headlights with many LEDs not recieving enough power. Possible relay issue?


If it has a balast check on it if not then u need a ballast to cracnk up the juice to the HID

Dec 11, 2014 | Cars & Trucks

2 Answers

How do I replace front HID light bulb? and where can I purchase parts for replacing?




  1. INSTALLATION GUIDE:


  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights


  3. Parts Identification:


  4. Projector Headlight


  5. Halo & L.E.D.


  6. Bottom of the Headlight:


  7. Ballast Bracket, Halo Wires(red/black)


  8. Turn Signal Adaptor


  9. TOOLS REQUIRE


  10. 10mm - 8mm socket


  11. Philip Screwdriver


  12. Crimper/Pliers


  13. For more information about how to install your vehicle, come visit our youtube page on


  14. http://www.youtube.com/spyderauto


  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.


  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.


  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.


  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.


  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.


  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.


  21. STEP:


  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.


  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.


  24. Factory Xenon Headlight


  25. Spyder Projector Headlight using Factory Xenon Lights






replace-front-hid-light-bulb-purchase-afy5cnsznmokzumyhdcbeseq-5-0.jpg

May 21, 2014 | BMW 335i Cars & Trucks

2 Answers

I have problem with hid light


follow this link to u-tube video not the exact vehicle but the principle will be the same,or search for your exact vehicle
How to replace low beam xenon HID bulbs 2006 BMW 330i

May 08, 2014 | 2007 BMW 335i Coupe

2 Answers

How to change headlight bulb


On the back of the headlight where the wires enter, you should be able to twist and remove the lamp holder. Be careful with the new bulb if it is halogen, do not touch the bulb!!

Apr 13, 2013 | 2000 Hyundai Sonata

1 Answer

2007 Ford F150 STX, I need the Wiring Diagram for Lights (Headlights, Running/Parking/Turn-Signal)


Go to either Autozone.com and register your vehicle for free, or alldatadiy.com for the same wiring diagrams. Powerbox layouts are also provided.

Now I want to add that if the new lights are like the HID factory type, you may need 2 Relays and heavier wiring to the lamps. Now sure if the Alternators are the same either.

I hope my solution helps.

Sep 18, 2012 | Ford F-150 Cars & Trucks

1 Answer

Scion tc brights indicator wont come on.


i did this and found that the fuse for the lights were blown look in your manual to see where the fuse is and replace it

Aug 21, 2012 | 2006 Scion tC

2 Answers

Lt. headlight low beam wont work after replacing the bulb.


I assume it didn't work before you changed the bulb either. You'll have to check for voltage at the bulb socket when the low beam headlights are turned on. If there is none you'll have to trace the wire back to where it splits from the right low beam headlight. If there is voltage there you have a problem with the new bulb.

Apr 10, 2011 | 1991 Lexus LS 400

2 Answers

How do you change front headlight blub 2008 sonata


how do you change front headlight blub 2008 sonata

Nov 28, 2009 | 2008 Hyundai Sonata

2 Answers

How to install hid on a bmw 325xi 2006


INSTALLATION GUIDE:
BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
Parts Identification:
Projector Headlight
Halo & L.E.D.
Bottom of the Headlight:
Ballast Bracket, Halo Wires(red/black)
Turn Signal Adaptor
TOOLS REQUIRE
10mm - 8mm socket
Philip Screwdriver
Crimper/Pliers
For more information about how to install your vehicle, come visit our youtube page on
http://www.youtube.com/spyderauto
Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
STEP:
Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
Factory Xenon Headlight
Spyder Projector Headlight using Factory Xenon Lights
STEP:
pls vote an diam giving you link also for better help BMW e46 HID Headlight Replace
install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-0.jpg

install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Oct 15, 2009 | 2003 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...