Question about Cars & Trucks

Open Question

How to replace a 1988 jeep wrangler turn signal lever

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: 1988 Wrangler Ignition Switch Removal

There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Posted on Jan 05, 2009

lebones337
  • 152 Answers

SOURCE: VACUUM HOSE DIAGRAM FOR 1988 JEEP WRANGLER 4.2 I6?

here is a link with all the vacum diagrams for your jeep. hope it helps.
http://www.autozone.com/addVehicleId,1076002/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528008ab9d

Posted on Feb 12, 2009

localwonder
  • 6784 Answers

SOURCE: my turn signal and flasher wont work.i replaced the lever on the

A flasher can be located in the fuse panel, under the dash in the wiring loom, in a glove box,\ or, under the hood.

Most flashers are located under the dashboard on the driver's side.


Posted on Jun 24, 2009

  • 15 Answers

SOURCE: my jeep wrangler hazard lights, turn signals and

replace the flashers, check fuse, check that the switch is grounded properly

Posted on Oct 04, 2009

  • 2 Answers

SOURCE: 2001 jeep wrangler sport ,fog lights on, switch off

I have a simular problem. Only mine does not some on. I tried to replace the turn signal switch assembly with a used one. The replacement work ok on the fog lights but the rest was bad. As near as I can figure it, the switch assemble is not well made and had many ways to go bad. Either replace the whole assemble or wire in a bipass switch. I am going to go with a bipass switch. I don't trust the new jeep products.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 Jeep Wrangler starting problems. I replaced the ignition module, spark plug wires, coil, distributor module, and my jeep will not start. It gets fuel, turns over, but still not starting. It is a 1988...


you are saying it is getting spark, and fuel, right? If it is getting spark, and fuel in to the throttle body, check compression-make sure the Mass Air Flow sensor is plugged in, and double check your spark-you say you replaced all those ignition items, but do not say that you have spark.

Jul 01, 2011 | 1988 Jeep Wrangler

1 Answer

How do you replace the blinker lever on the steering column of a 1993 Jeep Wrangler?


You will have to remove steering wheel,and lock plate,then remove the turn signal cam,and then there is a screw holding the lever to the turn signal switch.

May 17, 2010 | 1993 Jeep Wrangler

1 Answer

Where is the throttle body/butterfly plate on a 1988 jeep wrangler?


When you look down into the throttle body it is the plate that opens when you move the throttle lever (attached to the gas pedal cable)

Sep 09, 2009 | 1988 Jeep Wrangler

1 Answer

2001 jeep wrangler sport ,fog lights on, switch off


I have a simular problem. Only mine does not some on. I tried to replace the turn signal switch assembly with a used one. The replacement work ok on the fog lights but the rest was bad. As near as I can figure it, the switch assemble is not well made and had many ways to go bad. Either replace the whole assemble or wire in a bipass switch. I am going to go with a bipass switch. I don't trust the new jeep products.

Jun 25, 2009 | 2001 Jeep Wrangler

1 Answer

1998 Jeep Wrangler Electrical Short in Steering Column?


I had a similar problem with my 2000 Jeep TJ and I found the problem in the wiring harness under the hood.several wires were corroded and almost burnt off.If you remove the black tape which keeps the harness bundled together and if you see evidence of "green" type powder or "gook" it's most likely where the wires have faulted.

Dec 12, 2008 | 1988 Jeep Wrangler

1 Answer

YJ Blinker Relay


Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Aug 30, 2008 | 1988 Jeep Wrangler

1 Answer

1988 jeep wrangler no fuel


check your fuel pump relay and your ignition switch those numbers you gave for voltage are not right, please recheck that you have a ground and 12volts at the pump while cranking please rate -jeff

Jul 09, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...