Question about 1996 Honda Accord

1 Answer

Low beams work high beams dont

Also which may not be related is the light in the cabin temp window is only lit on the left side checked the fuses under dash

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Master
  • 1,013 Answers

The bulbs have 2 filaments, one for low beam and one for high beam. It's possible both high beam filaments are blown and you just need to replace the bulbs. You can check by measuring the voltage at the high beam terminal. You should see at least 12 volts when you turn on the high beams. If you do, it's the bulbs. If you don't it's likely the switch or the relay (assuming you've verified the fuses are good)

Posted on Jan 11, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

3 Answers

I have a 2006 ford escape and the passenger head light low beam will not work. Tried replacing the bulb, and check fuses nothing is working.. what else can I try?


Both your low beam and your high beam is protected by the same fuse, so it makes sense that the fuse is OK if the high beam is working on the passenger side. There are 3 fuses for the headlamps. Fuse #13 in the Battery Junction Box (20 Amp). If this fuse is blown, the headlamp relay will not have any power and neither high nor low beam on either side will work (you will have no headlamps at all) Then there is Fuses #2 and #3 (15 Amp) in the Battery Junction Box. #2 goes to the left low and high beam and #3 goes to the right low and high beam.
The headlamp switch uses a SINGLE CIRCUIT to control BOTH sides at the same time, so if one side works, the switch cannot be the problem. The headlamp relay provides power for fuses #2 and #3 and we already ascertained that these fuses must have power since we have working lights on both sides, so the relay cannot be the problem. A replacement bulb has already been tried, so that pretty much leaves us with a bad lamp socket. (Most likely cause) or a bad connection at splice #S122, which is located in the main wiring harness near the breakout for the left headlamp. (RED/BLACK wire)

May 16, 2011 | 2003 Ford Escape

1 Answer

Translating japanese to english on fuse box


is located under the dashboard on the driver's side. The fuse label is attached under the steering column. If something electrical in your vehicle stops working, check for a blown fuse first. Below table outlines detail fuse number, its ampere and circuits protected. honda-crv-interior-fuse-diagram-thumb.png
No.
Amps
Circuits Protected
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
7.5 15 10 7.5 (15) (20) _ 10 7.5 7.5 10 10 10 7.5 7.5 10 10 20 15 7.5 20 _ _ (20) 20 20 (20) 15 15 20 (15) 20 20 7.5 7.5 10 7.5 30
Power Window Relay Fuel Pump ACG ABS/VSA Heated Seats* Front Fog Lights* Not used Rear Wiper ODS (Occupant Detection System) Meter SRS Right Headlight High Beam Left Headlight High Beam Small Light (Interior) Small Light (Exterior) Right Headlight Low Beam Left Headlight Low Beam Main Headlight High Beam Small Lights MAIN TPMS Headlight Low Beam Not used Not used Moonroof* Door Lock Front Left Power Window HAC Option Rear Accessory Socket Accessory Front Right Power Window Accessory Power Socket on the Center Table* Rear Right Power Window Rear Left power window ACC Radio ACC Key lock HAC Daytime Running Lights Front Wiper

Dec 13, 2010 | 1997 Honda CR-V

2 Answers

2000 Ford Mustang GT. High beams BOTH WORK. Signal lights BOTH WORK. Low beam ONLY works on the right side. Both bulbs have been replaced. What is going on???? This is driving me mad!!


Have you checked the fuses yet? The low beams use 2 different fuse for the left and right lamps. The fuse for the left lamp is #10 in the central junction box located behind the dash to the left of the steering column.

Nov 09, 2010 | 2000 Ford Mustang

1 Answer

98 caviler low beam


98 caviler high beam left side dosent work canged bulb checked fuse and all good

Feb 06, 2010 | 1998 Chevrolet Cavalier

1 Answer

My passenger side low beam headlight is out. the driver side low beam headlight works fine. I replaced the bulb and the headlight still doesn't work. What should I look at next?


Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Dec 16, 2009 | 2004 Hyundai Santa Fe

1 Answer

Relay box location. there is a problem with the drivers and pasangers window wont go up or down and the head lights dont work but the side lights will. therefore i think its the hrad lights


Fuse for window regulator (circuit breaker) on 13 position auxiliary relay panel. The wiring connectors are located at the lower left and right side kick panels. The auxiliary relay panel is located above the lower kick panel above the pedals.

Headlight fuse location:
#18 High beam right 10A
#19 High beam left 10A
#20 Low beam right 15A
#21 Low beam left 15A

Daytime running light relay location on upper (auxiliary) relay panel. This are the only ones using relays regarding your question.

From April 1999
Position 7, Relay #173

Through March 1999
Position 8, Relay #173

Oct 17, 2009 | 2000 Volkswagen Beetle

2 Answers

Left side low beam not working


check low beam fuse and relay

Apr 14, 2009 | 2002 Cadillac Sts

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

Not finding what you are looking for?
1996 Honda Accord Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...