Question about 1986 Chevrolet C1500

1 Answer

86 pick-up chev

How to remove front manual hub on 86 chevrolet full size

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

You should see 6 small allen screws around hub,remove these and outer hub will slide off. then there will be a snap ring around axle remove this and also will be a large ring around outer part of hub and inside the rotor hub. remove this one and hub will slide out

Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size socket do i need for the drive axle/hub nut for a 1997 Chevrolet Cavalier?


I think that one is a 32mm...could b wrong tho..
I'd grab my 32 and 36 if I were going to take it off without looking

Sep 02, 2014 | 1997 Chevrolet Cavalier

1 Answer

2009 chev impala rear wheel hub


2009 chev impala, what is torque on front hubs

Aug 23, 2012 | 2009 Chevrolet Impala LS

1 Answer

I have a 1997 full size cinversion van (Chev Cobra) I can'y get the inside engine access compartment open. I took out 2 upper bolts and the side spring clamps. The storage compartment seems to be hooked...


Lift the carpet ,on the floor between the seats to locate 2 more bolts. When removed the cover is kinda hard to remove.Lift bottom of cover to pull back the front and try to put the front part of cover to pasenger seat. Then roll the cover over and out the door

Mar 02, 2011 | Chevrolet Chevy Cars & Trucks

2 Answers

Need vacum hose dirgram placement for 1986 chevy clebrty 2.8 sadan


037f845.jpg

Fig. 31: Chevrolet 2.8L VIN X 2BC - 1985-86 Federal models (click for zoom)

bd6b99a.jpg

Fig. 32: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi Federal models

086d0bd.jpg

Fig. 33: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi Canada models

f593b1d.jpg

Fig. 34: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi California models

f6a7573.jpg

Fig. 35: Chevrolet 2.8L VIN W TBI - 1985-86 Canada models


Hope this help (remember rated this).

Aug 04, 2010 | Chevrolet Celebrity Cars & Trucks

1 Answer

89 chev s10 how to replace front axles


prev.gif next.gif Halfshafts (Drive Axle) REMOVAL & INSTALLATION Fig. 1: A torn CV-boot requires removal of the driveshaft for overhaul 85387081.jpg
Fig. 2: On most vehicles. the caliper should be removed and supported out of the way 85387082.jpg
Fig. 3: Also on most vehicles, the tie rod end should be separated from the steering knuckle 85387083.jpg
Fig. 4: Once the lower shock fasteners are removed it may be compressed and wired up out of the way 85387084.jpg
Fig. 5: Loosen and remove the flange bolts 85387085.jpg
Fig. 6: Remove the cotter pin and retainer so the axle nut may be loosened 85387086.jpg
Fig. 7: A prybar may be used across to of the lug nuts in order to keep the hub from turning while loosening the nut 85387087.jpg
Fig. 8: Use a suitable axle shaft removal tool to drive the shaft from the hub 85387088.jpg
Fig. 9: If a driver tool is not available, thread the nut just flush with the shaft end and tab gently with a rubber or brass mallet 85387089.jpg
Fig. 10: During assembly, hold the hub from turning and torque the axle nut to specification 85387090.jpg
FRONT DRIVE AXLE Identification The front axle assembly used on most 4wd models covered by this manual utilizes a central disconnect type front axle/transfer case system which allows shifting in and out of 4wd when the vehicle is moving under most driving conditions. The axle has an aluminum carrier which includes a vacuum activated center lock feature. The axle on the MFI-Turbo is designed for full-time four wheel drive and therefore is not equipped with a disengagement feature. With this one exception, the MFI-Turbo and standard 4wd front axle assemblies are very similar. The drive axles employ completely flexible assemblies which consist of inner and outer constant velocity (CV) joints connected by an axle shaft. The inner CV joint is a "tri-pot'' design, which is completely flexible and can move in and out. The outer CV joint is a "Rzeppa'' design which is also flexible but cannot move in or out. NOTE: For more information on front axle identification, please refer to Section 1 of this manual. prev.gif next.gif

Jul 21, 2010 | 1988 Chevrolet S-10

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

1 Answer

What is the size of the front caliper bolts on a 2001 chev. blazer


Full size 3/8 allen (socket head) T40 torx on the small blazer replacement bolts can be 8 MM allen

Aug 16, 2009 | 2001 Chevrolet Blazer

1 Answer

1992 Chev 1/2 ton 4x4 front left wheel bearing replacement how to and tips


Instead of explaining step by step. I will guide you to a full free online repair manual for your entire vehicle. This will give you step by step directions, with illistrations.

Go to www.autozone.com, than register for free.
Than go to the site, select vehicle repair guides, pick your vehicle, and THERE YOU GO!
You now have the guide that will explain how to remove the cotter pin, cap, bearing, and everything else.

Jun 22, 2009 | 1992 Chevrolet C1500

1 Answer

Cannot remove automatic hubs


There is a small o- snapp ring under the grease around chrome hub. Clean gease and then remove with an automtive pick. That will lead to nother snapp ring. Exloded view autozone.com. You still need a spanner socket to remave bearing nut.

Mar 31, 2009 | 1996 Ford Bronco

1 Answer

Remove the front disc rotor


The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...