Question about Chrysler Concorde

1 Answer

Can i get another remote for my 1997 chrysler concorde

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 827 Answers

Sure most auto locksmiths have replacements, also they can program it

Posted on Jan 18, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1997 chrysler concord

My girlfriend's 95 concorde was having a problem that sounds like that. Some times when she started the car, the heater control console would not turn on but the heater would turn on full blast. I fixed it by replacing the control console with one that i picked up from the junk yard. Hope this helps you

Posted on Nov 12, 2008

old marine
  • 1992 Answers

SOURCE: i need to replace the serpentine belt on a 1997

Use AutoZone's online guide here.

Posted on Mar 03, 2009

moparownr
  • 667 Answers

SOURCE: torque specs needed

do you have a Haynes reapir manual or Chiltons? if not you can get one from autozone or some other parts places, or you might find one in your local library, inside that book are all the torque specs you can stand.

Posted on Mar 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: how do you replace the egr valve in a 1997

Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing

  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Posted on Sep 04, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to remove alternator from 1997 Chrysler

e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the firing order and plug gap


For 1997 Chrysler Concorde 3.5 liter SOHC V-6 VIN "F"...

9_20_2011_2_42_39_am.gif

Hope this helps (remember to rate and comment this answer).

Sep 10, 2011 | 1997 Chrysler Concorde

1 Answer

1997 chrysler concorde brakes good and adjusted properly but pedal is to the floor. Any suggestions?


If you know that the system is bled properly and there are no leaks at any of the wheel cylinders, lines, or calipers, then you probably have a bad master cylinder.

Mar 03, 2011 | 1997 Chrysler Concorde

1 Answer

1997 Chrysler Concorde LXI. Radio works its just


Try disconnecting the battery for five minutes and then reconnect. This may reset the memory in the radio.

Sep 16, 2010 | 1997 Chrysler Concorde

1 Answer

Where is the ac low pressure line in a 1997 chrysler concorde


find the ac compressor under the hood on the engine, the low side is the larger of the two lines from the compressor

May 07, 2010 | 1997 Chrysler Concorde

1 Answer

Need diagrahms to replace and install internal water pump for a 1997 Chrysler Concorde.


Your best bet would be to get the Haynes or Chilton repair manual from the local auto parts store for your vehicle. It should cost about $20.00.

Dec 18, 2009 | 1997 Chrysler Concorde

1 Answer

Where is the water pump located on a 1997 chrysler concord


If it's a 3.5, it's behind the timing cover. If it's a 3.3, it's on the lower driver's side. It has a smooth wheel on it. Hope this helps. PHil

Jan 11, 2009 | 1997 Chrysler Concorde

1 Answer

1997 chrysler concord


My girlfriend's 95 concorde was having a problem that sounds like that. Some times when she started the car, the heater control console would not turn on but the heater would turn on full blast. I fixed it by replacing the control console with one that i picked up from the junk yard. Hope this helps you

Oct 21, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...