Question about 1994 Mercury Villager

Open Question

How do i hot wire a 1994 mercury villager - 1994 Mercury Villager

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: 1994 mercury villager

if the car is stilling running hot check the antifreeze overflow bottle for a crack and to answer your question start the car and get it to normal temp while it is still running you open the overflow bottle fill it to the cold mark and keep adding coolant until all the bubbles are out of the system and put the cap back on right away

Posted on Jan 29, 2009

  • 454 Answers

SOURCE: i need a belt diagram for a 1994 mercury villager

Look under the hood, usually a belt diagram on the emissions sticker (look near the top of the radiator).

Posted on Oct 07, 2009

  • 78 Answers

SOURCE: how do I change a water pump

drain coolant first,take off serpentine belt loose 6 bolts on water pump take off water pump clean well,put new gasket than install new pump

Posted on Jan 10, 2010

emissionwiz
  • 74896 Answers

SOURCE: speedometer quit working

this car uses an electronic speedo head, u must rmove the speedometer from the dash and send it in for repair at an authorized ford electronics repair center.

Posted on Jan 18, 2010

c17hydro
  • 2984 Answers

SOURCE: where is a fuel pump located, for 1994 villager

In the tank!!!

Removal
CAUTION Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion.


The fuel pump and fuel tank sending unit are removed as an assembly.

  1. Remove the fuel tank. Please refer to Fuel Tank, Removal and Installation for the procedure.
  2. Clean the area around fuel pump.
  3. Remove the six fuel pump bolts.

    WARNING The fuel pump and fuel tank sending unit assembly must be tilted to remove it from the fuel tank. Do not lift the assembly straight out of the tank, or damage may occur to the sending unit.

  4. Lift the fuel pump and fuel tank sending unit assembly from the fuel tank and discard the gasket.


2d8596e.gif

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for an engine diagram for a 1994 Mercury Villager


go to yahoo group for villager-quest owners and read files and look at photos. If interested in shop manual for $15 plus postage, let me know.

Aug 06, 2011 | 1994 Mercury Villager

1 Answer

How to remplace a wather pump in a 94 mercury villager


I have shop manual & wiring book for 94 Villager for $25 plus postage. Let me know if interested.

go here for help too. It's an all day job but you can do it. Need to note where each bolt goes cause some are different sizes.

http://groups.yahoo.com/group/villagerquest/

Mar 31, 2010 | 1994 Mercury Villager

2 Answers

I need firing order for mercury villager 1994


it's 1-2-3-4-5-6.

#1 is on the passenger side rear and #3 & #5 are also on the back.

#2 is in front on passenger side. #4 & #6 are across the front.

go here for expert villager help.

http://groups.yahoo.com/group/villagerquest/

Jan 05, 2010 | 1994 Mercury Villager

1 Answer

1994 mercury villager has skip and engine service


Try disconnecting the battery for 2 hours. Then drive for 10 miles so the PCM can relearn. It may run rough for 10 miles.

If not ok, go to Villager website for expert team help free. Check files, ask questions

http://groups.yahoo.com/group/villagerquest/

Oct 31, 2009 | 1994 Mercury Villager

1 Answer

There are 4 wires at the fuel pump connector and they are all red, i know one is the ground but which one goes to the fuel pump


get a test light turn key on check it you have fonud the hot for the ing turn the key on like u are starting it u will find the other hot

Oct 05, 2009 | 1994 Mercury Villager

2 Answers

1994 mercury villager


Start with engine cool. Remove rad cap, top up coolant, start engine, & turn on heater (not defrost). let it run until up to normal operating temperature & radiator fan comes on, then shuts off. Let it do this about 3 times before you put rad cap back on & top up return bottle to proper level. Every once in a while, rev engine slightly for a few seconds while your doing it, to speed up bleed by increasing flow. Keep an eye on temperature gauge for too hot, and fan not coming on, if so, shut it off.

Jan 29, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
1994 Mercury Villager Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...