Question about 1997 Buick Century

Open Question

2005 buick lacrosse head bolt specs and sequence for 3.8 engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Keith100881
  • 74 Answers

SOURCE: remote for buick Lacross doesn't work, battery new. Can't figure how to reset it.

have to be reset by dealer usually 20 to 35 dollars to do so

Posted on May 16, 2009

  • 6 Answers

SOURCE: My remote won't start my 2005 Buick LaCross. I

Both my remotes no longer work. I will be ordering new ones off Ebay and having my dealer program them. New ones from Buick are very pricey.

Posted on Oct 20, 2009

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

  • 105 Answers

SOURCE: How do you change a tail light in 2005 Buick

I have a 2002 lesabre and suspect it is the same. The light assemblies are bolted to the car from the inside of the trunk. Mine has three sections. Left side of trunk, across the back of the trunk and right side of the trunk. Open the trunk and look thru the small holes in the back for nuts that hold on the sections. They may require a deep socket to reach. Also not all the nuts need to be loosened. Trial and error. Once the nuts are removed the light assemble is freed from the car. Don't let it fall and scratch the car. The wires will help hold it in place. The light holders usually turn/twist and pull out. A little bit of a pain, but not too difficult. Again the deep sockets are probably required.

Posted on Apr 25, 2010

  • 2841 Answers

SOURCE: I need a serpentine belt

It should be under the hood on a placard. If not someone has removed it. In that case here it is. a096361.png

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need transmission pan bolt pattern for 2008 Buick lacrosse cx v6 3.8 litre


I just snug a couple up on two sides of the pan and go around it until tight. This is not a critical sequence tighening, like doing heads.

Aug 26, 2016 | 2008 Buick LaCrosse CX

1 Answer

Cylinder head to engine block torque sequence and ft lbs


    images for Cylinder head to engine block torque and ...
    More images for Cylinder head to engine block torque and sequence

    Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

    boxwrench.net/specs/chevy_sb.htm
    their specs. Click Here! 3/8 Connecting Rod Bolt, Engine Oil, 45 ft-lbs. 11/32 Connecting Rod Bolt, Engine Oil, 35 ft-lbs. Cylinder Heads. Engine oil. (blind hole).

    [PDF]

Nov 29, 2015 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Torque specs for 2005 nissan altima 2.5


According to Haynes Manual, 2005 Nissan Altima, using BRAND NEW cylinder head bolts:

1 - Tighten in sequence (as pictured) to 37 ft-lbs.
2 - Tighten an additional 60 degrees.
3 - Loosen all bolts completely.
4 - Tighten in sequence 26 - 32 ft-lbs.
5 - Tighten in sequence an additonal 75 degrees.
6 - Tighten in sequence an additional 75 degrees.

Mar 23, 2012 | 2005 Nissan Altima 2.5

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

What is the cylinder head torque spec for a 2005 nissan sentra 1.8 liter engine


  1. For 1.8L engines, tighten the bolts in sequence, as follows:
    1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
    2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
    3. Step 3: Loosen bolts 1-10 completely.
    4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
    5. Step 5: Bolts 1-10 plus 50-55 degrees.
    6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).

      0900c152801afb79.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Cylinder head torque sequence-1.8L engine


      0900c152801afad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines

Nov 13, 2009 | 2005 Nissan Sentra

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1997 Buick Century Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...