Question about 1989 Chevrolet C1500

1 Answer

How do yoiu get the door hindges off of a 89 chevy 1500

My door is sagging real bad, i cannot seem to get the door off of the truck, am i missing something?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

To get the door off you have to take out the door pins. The top pin goes in upwards and the bottom pin downward. Make sure you put a jack under the door frame to ease pressure on the pins. Tap pins lightly to remove them. Just like a house door. You will need new bushings. If you find that the bushings are not fitting snug to the hinge, loose, you may need to drill the hole out a bit bigger, and use an over sized pin and bushing to replace it. Good luck, I hope this helps, please rate this solution

Posted on Jan 11, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ward_knutson
  • 64 Answers

SOURCE: 1998 chevy truck 1500 door latches

The handle mechanism wears over time. I went on eBay, bought a color matching handle for under $20 and replaced it myself. You have to be careful when removing the plastic panel bezel that surrounds the handle, drill out two rivets and your door will open like new!

Posted on Nov 25, 2008

delgriffith
  • 97 Answers

SOURCE: 89 chevy truck misses and dies on acceleration

try the mass air flow sensor

Posted on Jul 08, 2009

  • 5 Answers

SOURCE: what size speaker will fix in my truck i have a

6x9

Posted on Sep 30, 2009

SOURCE: Driver side door on a 1990 Chevy 1500 seriously sagging

try shims in back of hing mount sounds like it got bent or rusted out and weak

Posted on Nov 09, 2009

pyroshain
  • 42 Answers

SOURCE: Repair door sag on a Chevy Suburan

The door hinges have pins in them. The pins have bushings in the hinge. If you go down to your local parts parts store you will be able to purchase them. They are brass colored. You will need to unbolt the doors and use a punch to hammer out the bushings and use a hammer to replace them.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Prado 120 back door sagging


you can only do limited adjustments, First open the door and grab it by the back edge, see if it moves up and down, if it does the hinges are worn and need to be replaced. If no then open the front door and you will see the hinges of the back door, Loosen the bolts and have someone lift the back of the door slightly, Tighten then re-check. if needed keep trying until it sits right. You may also have to adjust the rear latch which is simply a matter of loosening the screws and adjusting as required.

Mar 11, 2012 | Toyota Land Cruiser Cars & Trucks

1 Answer

My 1990 GMC Sierra 1500 ha a problem with the


You need to get the hinges on the door fixed. The bushings are worn out causing the door to sag. See a body shop.

Mar 01, 2010 | 1990 GMC Sierra

1 Answer

1998 Chevrolet 5.7 Vortec Problems.


Most likely the intake gaskets are bad. they will sag in the middle over time and allow a vacuum leak between the head and intake. recommend replacing the gaskets with the steel instead of plastic ones.

Jan 19, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Steering colunm diragram for a 89 chevy c 1500


Autozone ,Chilton manual for about 10.00 has this info

Oct 04, 2009 | 1985 Chevrolet Chevy

1 Answer

1994 chevy camaro driver door will not open. all


With the window down, reach inside and find a place to the rear on the door that you can lift from. Then try lifting while you pull on the handle. I have seen the door hinge bushings get bad and let door sag, and then the latch won't release from the striker.
Its the only thing I can think of as being the problem if everything is moving inside the door as it should. If you do get it open you can check the bushings by having the door almost to the closed position and lift up on it if they are bad you will feel the play in the bushings. If this is the problem you can replace just the bushings and not the whole hinge. Thats when you are probably going to have to talk to a body shop.

Apr 05, 2009 | 1994 Chevrolet Camaro

1 Answer

Can't open door


inspect the door hindge pins and busings it sounds like they are getting worn out and maybe due for replacement. also look and see if the spring in the hindge is still their. if all is well have the door adjusted properly to repair your problem.

Mar 22, 2009 | 1996 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...